FireCADCalc

Ethanol–Water Dew Point: Vapour → Condensate

Dew point and the liquid first condensed from an ethanol–water vapour of known strength at about 1 atm (dephlegmator, partial condenser), Wilson model.

Distillery and ethanolIAPWS-IF97 (water and steam)

Inputs

Examples: Vapour 0.60 mole fractionVapour 40 % vol

Model fitted at 1 atm; use 0.9–1.2 atm.

Results

Vapour mole fraction60.000%
Dew point81.067°C
First condensate mole fraction35.627%
First condensate strength66.400%
Strength of the total condensate84.931%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Vapour 0.60 mole fraction. The inputs, in the units selected above:

InputValue
Vapour strength entered asMole fraction
Vapour strength60.000 %
Pressure101.33 kPa

Applying the formula below gives:

ResultValue
Vapour mole fraction60.000 %
Dew point81.067 °C
First condensate mole fraction35.627 %
First condensate strength66.400 %
Strength of the total condensate84.931 %

Open this example in the calculator and change any input.

Formula

\(y_1 = \frac{x_1\gamma_1 p_1^s(T_d)}{P}, \quad \sum y_i = 1\)

Variables

Symbol Meaning SI unit
\(\text{basis}\) Vapour strength entered as -
\(s_y\) Vapour strength -
\(P\) Pressure Pa
\(y_1\) Vapour mole fraction -
\(T_d\) Dew point K
\(x_1\) First condensate mole fraction -
\(q_x\) First condensate strength -
\(q_y\) Strength of the total condensate -
\(\gamma_1, \gamma_2\) Activity coefficients of ethanol and water (Wilson) -
\(p_1^s, p_2^s\) Vapour pressures of ethanol and water Pa

Method and standards

Dew point by bisection on the liquid composition with the bubble-point solution.

Where it is used

  • Dephlegmator and partial condenser design.
  • Interpreting vapour-line temperatures.

Common mistakes

  • Assuming condensate equals vapour strength at the dew point.

Assumptions and limits

  • Wilson energies fitted at 1 atm; 0.9–1.2 atm only.
  • Binary ethanol–water; congeners and dissolved solids ignored.

References

  • Ethanol–water VLE at about 1 atm: Wilson equation (Perry's Chemical Engineers' Handbook, 9th ed., sec. 4) with energies 399 and 933 cal/mol fitted to FireCAD ethanol–water x–y–T data at 101.325 kPa; ethanol vapour pressure Perry's 9th ed. Table 2-8; water IAPWS-IF97
  • Checked against Gmehling and Onken
  • DECHEMA Chemistry Data Series vol. I/1
  • as quoted in Perry's 9th ed. sec. 13 (simple batch distillation example)

Questions and answers

Why is the first condensate weaker than the vapour?

Water condenses preferentially: that is how a dephlegmator returns a weaker reflux and passes a richer vapour.

What is the total condensate strength?

If all the vapour is condensed, the liquid has the vapour's own composition.

Why must the vapour be below the azeotrope?

Above it the equilibrium reverses and this inversion has no single answer.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.