FireCADCalc

Notch Root Stress and Strain by Neuber's Rule

Local stress and strain at a yielding notch root from K_t, nominal stress and the cyclic Ramberg–Osgood curve, by Neuber's rule.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationRefinery and petrochemicalChemical and fertiliserPulp and paper

Inputs

Examples: K_t 2.5, 200 MPa, K′ 1,200 MPa, n′ 0.15Aluminium K_t 3, 120 MPa, K′ 650 MPa, n′ 0.07

Results

Neuber's rule σε = (K_tS)²/E with the cyclic stress–strain curve ε = σ/E + (σ/K')^(1/n'). Use K_f (fatigue notch factor) instead of K_t for fatigue life when notch sensitivity is low. Nominal stress assumed elastic.

Notch root stress354.02MPa
Notch root strain0.005156
Stress concentration (actual)2.9502
Strain concentration3.0507

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: K_t 2.5, 200 MPa, K′ 1,200 MPa, n′ 0.15. The inputs, in the units selected above:

InputValue
Elastic stress concentration factor2.5000 -
Nominal stress200.00 MPa
Elastic modulus200.00 GPa
Cyclic strength coefficient1,200.0 MPa
Cyclic strain-hardening exponent0.15000 -

Applying the formula below gives:

ResultValue
Notch root stress418.61 MPa
Notch root strain0.002986
Stress concentration (actual)2.0931
Strain concentration2.9861

Open this example in the calculator and change any input.

Formula

\(\sigma\varepsilon = \frac{(K_tS)^2}{E}, \quad \varepsilon = \frac{\sigma}{E} + \left(\frac{\sigma}{K'}\right)^{1/n'}\)

Variables

Symbol Meaning SI unit
\(K_t\) Elastic stress concentration factor -
\(S\) Nominal stress Pa
\(E\) Elastic modulus Pa
\(K'\) Cyclic strength coefficient Pa
\(n'\) Cyclic strain-hardening exponent -
\(\sigma\) Notch root stress Pa
\(\varepsilon\) Notch root strain -
\(K_\sigma\) Stress concentration (actual) -
\(K_\varepsilon\) Strain concentration -

Method and standards

Neuber's rule.

Where it is used

  • Low-cycle fatigue of notched parts.
  • Start-up and shut-down cycles of pressure parts.

Common mistakes

  • Using monotonic instead of cyclic properties.
  • Applying it with yielded nominal sections.

Assumptions and limits

  • Elastic nominal section; uniaxial. A warning appears when S exceeds the cyclic 0.2 % offset yield strength K'(0.002)^n'.

References

  • Neuber (1961) rule with the Ramberg–Osgood cyclic curve (Dowling, Mechanical Behavior of Materials, 4th ed. (Pearson, 2013), ch. 14)

Questions and answers

Why not just K_t × S?

Once the notch root yields, the elastic answer overstates stress and understates strain; strain controls low-cycle fatigue.

Where do K' and n' come from?

From cyclic stress–strain tests; handbooks list them for common steels and aluminium alloys.

What do the defaults represent?

A notch with K_t = 2.5 under 200 MPa nominal in a steel with K' = 1,200 MPa, n' = 0.15.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.