FireCADCalc

Two-Product Formula: Recovery, Yield and Separation Efficiency

Concentrate and tailings rates, metal recovery, ratio of concentration, enrichment ratio and Schulz separation efficiency from three stream assays.

Inputs

Examples: Wills Example 3.8, zinc flotation (sphalerite)Copper rougher, chalcopyriteTin gravity, cassiterite

Zn in sphalerite 67.1 %, Cu in chalcopyrite 34.6 %, Pb in galena 86.6 %, Sn in cassiterite 78.6 %

Results

Assays of the three streams taken at the same time; the formula assumes steady state and no other product. Separation efficiency is recovery of the mineral less recovery of gangue (Schulz), assuming the metal is in one mineral only.

Yield (mass to concentrate)2.5439%
Ratio of concentration39.310
Enrichment ratio35.000
Metal recovery to concentrate89.036%
Concentrate rate63.597t/h
Tailings rate2,436.4t/h
Gangue recovery to concentrate0.49842%
Separation efficiency (Schulz)88.538%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Wills Example 3.8, zinc flotation (sphalerite). The inputs, in the units selected above:

InputValue
Feed assay (metal)3.9300 %
Concentrate assay52.070 %
Tailings assay0.49000 %
Feed rate (dry solids)100.00 t/h
Metal content of the valuable mineral67.098 %

Applying the formula below gives:

ResultValue
Yield (mass to concentrate)6.6693 %
Ratio of concentration14.994
Enrichment ratio13.249
Metal recovery to concentrate88.363 %
Concentrate rate6.6693 t/h
Tailings rate93.331 t/h
Gangue recovery to concentrate1.5866 %
Separation efficiency (Schulz)86.777 %

Open this example in the calculator and change any input.

Formula

\(\frac{C}{F} = \frac{f - t}{c - t}, \quad R = \frac{C c}{F f}, \quad SE = R - R_g = \frac{C}{F}\frac{m(c - f)}{f(m - f)}\)

Variables

Symbol Meaning SI unit
\(f\) Feed assay (metal) -
\(c\) Concentrate assay -
\(t\) Tailings assay -
\(F\) Feed rate (dry solids) kg/s
\(m\) Metal content of the valuable mineral -
\(C/F\) Yield (mass to concentrate) -
\(F/C\) Ratio of concentration -
\(c/f\) Enrichment ratio -
\(R\) Metal recovery to concentrate -
\(C\) Concentrate rate kg/s
\(T\) Tailings rate kg/s
\(R_g\) Gangue recovery to concentrate -
\(SE\) Separation efficiency (Schulz) -

Method and standards

Two-product formula and Schulz separation efficiency.

Where it is used

  • Daily metallurgical accounting in concentrators.
  • Comparing operating conditions on a grade-recovery basis.

Common mistakes

  • Mixing percent and fraction assays.
  • Applying it to a circuit with more than two products.

Assumptions and limits

  • Steady state; metal in one mineral.

References

  • Wills and Finch
  • Wills' Mineral Processing Technology
  • 8th ed. (Butterworth-Heinemann, 2016)
  • ch. 1
  • eqs. 1.1-1.5 (Schulz, 1970) and ch. 3
  • eqs. 3.23-3.27
  • Examples 1.3 and 3.8

Questions and answers

Why use assays instead of weighing the products?

Concentrate and tailings flows are rarely weighed; the assays of three samples fix the split through the metal balance.

What is a good separation efficiency?

It is recovery of the valuable mineral less recovery of gangue; 100 % is a perfect separation and 0 % no separation at all.

What do the defaults represent?

Wills's Example 3.8: zinc flotation with 3.93 % Zn feed, 52.07 % concentrate and 0.49 % tailings (6.7 % yield, 88.4 % recovery).

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.