FireCADCalc

Continuous Fryer: Water Evaporated, Oil Uptake and Heat

Water evaporated, oil absorbed and heat load of a continuous fryer from product feed, moisture in and out and oil content of the fried product.

Food, dairy and textile

Inputs

Examples: 2 t/h potato slices to chipsFries par-fry

Results

Oil taken up must be replaced by fresh oil; a high turnover keeps the oil fresh.

Fried product2,069.0kg/h
Water evaporated1,055.2kg/h
Oil taken up124.14kg/h
Fryer heat load1,069.9kW

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 2 t/h potato slices to chips. The inputs, in the units selected above:

InputValue
Raw product feed2,000.0 kg/h
Moisture in the raw product78.000 %
Moisture in the fried product2.0000 %
Oil in the fried product34.000 %
Product specific heat3.5000 kJ/(kg·K)
Product in15.000 °C
Losses share15.000 %

Applying the formula below gives:

ResultValue
Fried product687.50 kg/h
Water evaporated1,546.2 kg/h
Oil taken up233.75 kg/h
Fryer heat load1,334.9 kW

Open this example in the calculator and change any input.

Formula

\(\dot M_p = \frac{\dot M(1 - w_1)}{1 - w_2 - o_2}, \quad \dot E = \dot M w_1 - \dot M_p w_2, \quad Q = \frac{\dot M c_p(100\,°C - T_1) + \dot E\lambda}{1 - \varepsilon}\)

Variables

Symbol Meaning SI unit
\(\dot M\) Raw product feed kg/s
\(w_1\) Moisture in the raw product -
\(w_2\) Moisture in the fried product -
\(o_2\) Oil in the fried product -
\(c_p\) Product specific heat J/(kg·K)
\(T_1\) Product in K
\(\varepsilon\) Losses share -
\(\dot M_p\) Fried product kg/s
\(\dot E\) Water evaporated kg/s
\(\dot M_o\) Oil taken up kg/s
\(Q\) Fryer heat load W

Method and standards

Solids, water and oil balances.

Where it is used

  • Fryer sizing and heater duty.

Common mistakes

  • Ignoring oil uptake in the product mass.
  • Using wet-basis moisture as dry-basis.

Assumptions and limits

  • Product heated to 100 °C; λ at 100 °C.
  • Not included: heating the fresh make-up oil from storage to frying temperature, and heating low-moisture products (crisps) above 100 °C towards the oil temperature. For such products the load is underestimated; add these terms or raise the losses share.

References

  • Mass and energy balances (definitions); latent heat of water 2 257 kJ/kg at 100 °C

Questions and answers

Why does oil uptake matter?

It is the fresh oil the fryer consumes and sets oil turnover.

Where does the heat go?

Mostly to evaporate water; heating the product to 100 °C is a small part.

How is the fryer heated?

Usually thermic fluid or direct-fired heat exchangers.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.