FireCADCalc

Freezing Time by Plank's Equation

Freezing time of a slab, cylinder or sphere of food from density, latent heat, freezing point, medium temperature, size, h and frozen conductivity (Plank).

Food, dairy and textile

Inputs

Examples: 50 mm slab in −30 °C air, h 25Sphere 30 mm, h 50

Results

Plank gives the phase-change time only; pre-cooling and sub-cooling add to it.

Shape factor P0.50000
Shape factor R0.12500
Freezing time2.9969h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 50 mm slab in −30 °C air, h 25. The inputs, in the units selected above:

InputValue
ShapeInfinite slab (a = thickness)
Thickness or diameter50.000 mm
Density1,000.0 kg/m³
Latent heat of the food (per kg)250.00 kJ/kg
Initial freezing point-2.0000 °C
Freezing medium temperature-30.000 °C
Surface heat transfer coefficient25.000 W/(m²·K)
Conductivity of the frozen food1.5000 W/(m·K)

Applying the formula below gives:

ResultValue
Shape factor P0.50000
Shape factor R0.12500
Freezing time2.9969 h

Open this example in the calculator and change any input.

Formula

\(t_f = \frac{\rho\lambda}{T_f - T_a}\left(\frac{Pa}{h} + \frac{Ra^2}{k}\right)\)

Variables

Symbol Meaning SI unit
\(\text{shape}\) Shape -
\(a\) Thickness or diameter m
\(\rho\) Density kg/m³
\(\lambda\) Latent heat of the food (per kg) J/kg
\(T_f\) Initial freezing point K
\(T_a\) Freezing medium temperature K
\(h\) Surface heat transfer coefficient W/(m²·K)
\(k\) Conductivity of the frozen food W/(m·K)
\(P\) Shape factor P -
\(R\) Shape factor R -
\(t_f\) Freezing time s

Method and standards

Plank's equation.

Where it is used

  • Freezer design and throughput.

Common mistakes

  • Using unfrozen conductivity.
  • Ignoring packaging resistance in h.

Assumptions and limits

  • Uniform freezing point; no sensible heat. Plank is known to underestimate practical freezing times because it leaves out pre-cooling to the freezing point and tempering below it; methods that add these (for example Pham or Cleland and Earle) are not offered here, so allow a margin.

References

  • Plank's equation: t = ρλ/(T_f − T_a) · (P a/h + R a²/k); P
  • R = 1/2
  • 1/8 (slab)
  • 1/4
  • 1/16 (cylinder)
  • 1/6
  • 1/24 (sphere)

Questions and answers

What does Plank assume?

The food starts at its freezing point, freezes at one temperature and the frozen layer conducts steadily.

Why does size matter so much?

The conduction term grows with the square of thickness.

What latent heat should I use?

Water content × 334 kJ/kg (the frozen share of it).

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.