FireCADCalc

CFB Furnace Cross-Section: Grate Heat Release and Velocity

Grate heat release from superficial velocity and excess air (3.3 U₀/EAC MW/m², Basu Eq. 4.21) and the furnace cross-section for a heat input.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperBoiler

Inputs

Examples: 300 MW at 1.6 m/s (300 K), 20 % excessBubbling bed 50 MW at 0.6 m/s

Results

U₀ is referred to 300 K; at a typical 850 °C furnace temperature the actual velocity is about 2.2 m/s (×3.7, before the gas volume added by combustion).

The constant 3.3 MW/m² per m/s is for average fossil fuels; biomass and high-moisture fuels release a different heat per unit of air.

The velocity from the gas flow (0.51 m/s) differs from U₀ (0.60 m/s) by more than 10 %: check the gas flow, the excess air or U₀.

Grate heat release rate1.5840MW/m²
Furnace cross-section31.566m²
Velocity at 300 K from the gas flow0.50688m/s

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 300 MW at 1.6 m/s (300 K), 20 % excess. The inputs, in the units selected above:

InputValue
Heat input (HHV)300.00 MW
Superficial velocity referred to 300 K1.6000 m/s
Excess air coefficient (1.2 = 20 % excess)1.2000 -
Combustion air volume flow at 300 K (for the check; 0 = none)342,000 m³/h

Applying the formula below gives:

ResultValue
Grate heat release rate4.4000 MW/m²
Furnace cross-section68.182 m²
Velocity at 300 K from the gas flow1.3933 m/s

Open this example in the calculator and change any input.

Formula

\(q_A = \frac{3.3U_0}{EAC}\ \mathrm{MW/m^2}, \quad A = \frac{Q}{q_A}, \quad U_{check} = \frac{\dot V_{300}}{A}\)

Variables

Symbol Meaning SI unit
\(Q\) Heat input (HHV) W
\(U_0\) Superficial velocity referred to 300 K m/s
\(EAC\) Excess air coefficient (1.2 = 20 % excess) -
\(\dot V_{300}\) Combustion air volume flow at 300 K (for the check) m³/s
\(q_A\) Grate heat release rate W/m²
\(A\) Furnace cross-section m²
\(U_{check}\) Velocity at 300 K from the gas flow m/s

Method and standards

Basu's Eq. (4.21).

Where it is used

  • First sizing of CFB and BFB furnaces.

Common mistakes

  • Using actual velocity at bed temperature for U₀.
  • Ignoring excess air.

Assumptions and limits

  • Average fossil fuels: about 3.3 MW per m² for each m/s of air at 300 K. Biomass and wet fuels differ.
  • Eq. (4.21) is in terms of the air velocity, so the check uses the combustion air flow at 300 K, not the flue gas flow.
  • The check velocity is shown only when a gas flow is entered; a warning appears when it differs from U₀ by more than 10 %.

References

  • Basu
  • Circulating Fluidized Bed Boilers: Design
  • Operation and Maintenance (Springer, 2015)
  • ch. 4
  • Eq. (4.21) (Waters 1975)

Questions and answers

Why is heat release tied to velocity?

Air per MJ of fuel is nearly constant, so the furnace can burn only as much fuel as the air passing through it.

Why referred to 300 K?

It fixes the air mass flow independent of furnace temperature.

What is typical?

CFB boilers release about 3–5 MW/m² of grate; bubbling beds about 1–2.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.