Worked example
Example: Drum 1.2 m bore, 90 mm. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Inner radius | 0.60000 m |
| Outer radius | 0.69000 m |
| Inner minus outer surface temperature | 30.000 K |
| Internal pressure (gauge) | 45.000 bar |
| Young's modulus | 195.00 GPa |
| Linear expansion coefficient | 13.000 µm/(m·K) |
| Poisson's ratio | 0.30000 - |
Applying the formula below gives:
| Result | Value |
|---|---|
| Thermal hoop stress, inner surface | -56.849 MPa |
| Thermal hoop stress, outer surface | 51.794 MPa |
| Pressure hoop stress, inner surface | 32.407 MPa |
| Pressure hoop stress, outer surface | 27.907 MPa |
| Total hoop stress, inner surface | -24.442 MPa |
| Total hoop stress, outer surface | 79.701 MPa |
Open this example in the calculator and change any input.
Formula
\(\sigma_{\theta,T}(r_i) = \frac{E\beta\Delta T}{2(1-\nu)\ln(r_o/r_i)}\left[1 - \frac{2r_o^2}{r_o^2 - r_i^2}\ln\frac{r_o}{r_i}\right], \quad \sigma_{\theta,p}(r_i) = p\frac{r_o^2 + r_i^2}{r_o^2 - r_i^2}\)
\(\sigma_{\theta,T}(r_o) = \frac{E\beta\Delta T}{2(1-\nu)\ln(r_o/r_i)}\left[1 - \frac{2r_i^2}{r_o^2 - r_i^2}\ln\frac{r_o}{r_i}\right], \quad \sigma_{\theta,p}(r_o) = p\frac{2r_i^2}{r_o^2 - r_i^2}, \quad \sigma_\theta = \sigma_{\theta,T} + \sigma_{\theta,p}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(r_i\) | Inner radius | m |
| \(r_o\) | Outer radius | m |
| \(\Delta T\) | Inner minus outer surface temperature | K |
| \(p\) | Internal pressure (gauge) | Pa |
| \(E\) | Young's modulus | Pa |
| \(\beta\) | Linear expansion coefficient | 1/K |
| \(\nu\) | Poisson's ratio | - |
| \(\sigma_{\theta,T}(r_i)\) | Thermal hoop stress, inner surface | Pa |
| \(\sigma_{\theta,T}(r_o)\) | Thermal hoop stress, outer surface | Pa |
| \(\sigma_{\theta,p}(r_i)\) | Pressure hoop stress, inner surface | Pa |
| \(\sigma_{\theta,p}(r_o)\) | Pressure hoop stress, outer surface | Pa |
| \(\sigma_\theta(r_i)\) | Total hoop stress, inner surface | Pa |
| \(\sigma_\theta(r_o)\) | Total hoop stress, outer surface | Pa |
Method and standards
Thermal hoop stresses of a long cylinder with a steady logarithmic temperature distribution through the wall (Timoshenko and Goodier), added to the Lamé hoop stresses from internal gauge pressure at the inner and outer surfaces.
Where it is used
- Drum and header stress checks.
- Teaching thermal stress.
Common mistakes
- Sign of ΔT reversed.
Assumptions and limits
- Long cylinder, elastic, steady.
- Hoop stresses only. The axial thermal stress (equal to the hoop thermal stress at the surfaces for a long cylinder with free ends) and the radial pressure stress (−p inside) are not shown, so no equivalent (Tresca or von Mises) stress is given for comparison with allowables.
References
- Thermal stresses in a long thick cylinder with a steady logarithmic temperature profile (Timoshenko and Goodier, Theory of Elasticity, 3rd ed., McGraw-Hill, 1970); Lamé pressure stresses
Questions and answers
Which way does the thermal stress act?
When the inside is hotter, the inner surface is in compression and the outer in tension.
Why add pressure stress?
The surfaces see both; heating from inside relieves the inner pressure tension.
Is this the start-up case?
No, it is the steady profile; fast transients give larger differences.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.