FireCADCalc

Fluid-Elastic Instability Critical Velocity (Connors)

Critical gap velocity for fluid-elastic instability of a tube array by Connors' equation, from natural frequency, mass, damping and fluid density.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolBoilerEconomiser and air preheater

Inputs

Examples: Gas bankLiquid-side tubes

Results

Gap velocity above half the critical value: margin is thin; designs commonly keep v well below v_c.

Log decrement 2πζ0.12566
Critical gap velocity1.6209m/s
Velocity ratio92.538%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Gas bank. The inputs, in the units selected above:

InputValue
Tube natural frequency60.000 Hz
Tube outside diameter50.800 mm
Mass per metre (with added mass)4.0000 kg/m
Damping ratio1.0000 %
Fluid density0.60000 kg/m³
Connors constant3.3000 -
Actual gap velocity12.000 m/s

Applying the formula below gives:

ResultValue
Log decrement 2πζ0.062832
Critical gap velocity128.15 m/s
Velocity ratio9.3642 %

Open this example in the calculator and change any input.

Formula

\(v_c = K f_n d\sqrt{\frac{m\,\delta}{\rho d^2}}, \quad \delta = 2\pi\zeta\)

Variables

Symbol Meaning SI unit
\(f_n\) Tube natural frequency 1/s
\(d\) Tube outside diameter m
\(m\) Mass per metre (with added mass) kg/m
\(\zeta\) Damping ratio -
\(\rho\) Fluid density kg/m³
\(K\) Connors constant -
\(v_g\) Actual gap velocity m/s
\(\delta\) Log decrement 2πζ -
\(v_c\) Critical gap velocity m/s
\(v_g/v_c\) Velocity ratio -

Method and standards

Connors' equation for the critical gap velocity of fluid-elastic instability (Connors 1970, as given by Blevins), with the log decrement \(\delta = 2\pi\zeta\). The constant \(K\) depends on the array pattern and is your input (about 2.4–4; 3.3 is common for design). A note appears when the gap velocity exceeds half the critical value, a FireCAD screening margin; at or above the critical value instability is predicted.

Where it is used

  • Tube bank vibration screening.

Common mistakes

  • Approach velocity used for gap velocity.

Assumptions and limits

  • Uniform cross-flow; the mass per metre must include the added mass of the fluid and the tube contents.

References

  • Connors (1970) v_c/(f_n d) = K [m δ/(ρ d²)]^½ (Blevins, Flow-Induced Vibration); K by array pattern (user input)

Questions and answers

What is fluid-elastic instability?

Above a critical velocity the flow feeds energy into tube motion faster than damping removes it; amplitudes grow quickly.

Which K?

Connors' constant depends on the array; values around 2.4–4 are used, often 3.3 for design.

Gas or liquid?

Both; gas flows have low density, so the critical velocity is high, but gas velocities are high too.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.