Worked example
Example: Quadruple. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Number of effects | 4.0000 - |
| Entrainment ratio | 1.8000 - |
| Total evaporation | 80,000 kg/h |
| Vapour bled from effect 1 | 11,000 kg/h |
| Vapour bled from effect 2 | 3,500.0 kg/h |
| Vapour bled from effect 3 | 6,000.0 kg/h |
| Exhaust steam produced by the drives | 25,000 kg/h |
| Exhaust used by the pans | 4,000.0 kg/h |
| Exhaust used by the heaters | 3,000.0 kg/h |
Applying the formula below gives:
| Result | Value |
|---|---|
| Most motive steam | 9,310.3 kg/h |
| Vapour then aspirated | 16,759 kg/h |
| Least vapour to the condenser | 6,810.3 kg/h |
Open this example in the calculator and change any input.
Formula
\(q \le \frac{E + (n-1)P_1 + (n-2)P_2 + (n-3)P_3 - n(M - C - R)}{n + \mu}, \quad y = \mu q\)
\(x \ge \frac{E - P_1 - 2P_2 - 3P_3 - \mu(P_1 + P_2 + P_3) + \mu(M - C - R)}{n + \mu}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(n\) | Number of effects | - |
| \(\mu\) | Entrainment ratio | - |
| \(E\) | Total evaporation | kg/s |
| \(P_1\) | Vapour bled from effect 1 | kg/s |
| \(P_2\) | Vapour bled from effect 2 | kg/s |
| \(P_3\) | Vapour bled from effect 3 | kg/s |
| \(M\) | Exhaust steam produced by the drives | kg/s |
| \(C\) | Exhaust used by the pans | kg/s |
| \(R\) | Exhaust used by the heaters | kg/s |
| \(q_{max}\) | Most motive steam | kg/s |
| \(y_{max}\) | Vapour then aspirated | kg/s |
| \(x_{min}\) | Least vapour to the condenser | kg/s |
Method and standards
Hugot's exhaust balance with a first-effect thermocompressor.
Where it is used
- Sizing and regulating thermocompressors.
- Factory steam balances.
Common mistakes
- Leaving pan vapour bleeding out of P.
- Ignoring exhaust losses in M.
Assumptions and limits
- Thermocompressor on the first effect.
- Bleeding from effects 1 to 3 only (no P₄ input for 5 effects). With 3 effects P₃ is bled from the last effect: it does not change q_max but reduces the vapour to the condenser.
- A negative x_min (bleeding beyond what the evaporator supplies) is rejected.
References
- Hugot
- Handbook of Cane Sugar Engineering
- 3rd ed. (Elsevier, 1986)
- ch. 32
- installation of a thermo-compressor
- eqns 32.52–32.62
- pp. 603–606
Questions and answers
Why a limit?
Thermocompression saves make-up steam only until exhaust from the drives covers the factory; beyond that it wastes exhaust.
What are M, C and R?
Exhaust produced by turbines and engines, and the exhaust used by pans and heaters.
Why a minimum to the condenser?
With maximum thermocompression the later effects still need a minimum of vapour passing through.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.