FireCADCalc

Phosphoric Acid Dose for Juice Clarification

Phosphoric acid to raise juice P₂O₅ to a target, as P₂O₅ added, pure H₃PO₄ and commercial acid by mass and volume, by stoichiometry.

Sugar mill and cogeneration

Inputs

Examples: Raise 150 to 300 ppmAlready enough

Density of the acid at the strength entered (85 % acid is about 1 685 kg/m³); it is not derived from the strength, so change both together.

Results

The juice already holds the target P₂O₅: no acid needed.

P₂O₅ added0kg/h
Pure H₃PO₄0kg/h
Commercial acid0kg/h
Commercial acid volume0L/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Raise 150 to 300 ppm. The inputs, in the units selected above:

InputValue
Juice flow250.00 m³/h
Target P₂O₅ in juice300.00 mg/L
P₂O₅ already in juice150.00 mg/L
Acid strength (H₃PO₄ mass fraction)85.000 %
Acid density1,685.0 kg/m³

Applying the formula below gives:

ResultValue
P₂O₅ added37.500 kg/h
Pure H₃PO₄51.778 kg/h
Commercial acid60.916 kg/h
Commercial acid volume36.152 L/h

Open this example in the calculator and change any input.

Formula

\(\dot m_{H_3PO_4} = \dot m_{P_2O_5}\frac{2 M_{H_3PO_4}}{M_{P_2O_5}}, \quad \dot m_a = \frac{\dot m_{H_3PO_4}}{w}\)

Variables

Symbol Meaning SI unit
\(\dot V_j\) Juice flow m³/s
\(c_t\) Target P₂O₅ in juice kg/m³
\(c_0\) P₂O₅ already in juice kg/m³
\(w\) Acid strength (H₃PO₄ mass fraction) -
\(\rho_a\) Acid density kg/m³
\(\dot m_{P_2O_5}\) P₂O₅ added kg/s
\(\dot m_{H_3PO_4}\) Pure H₃PO₄ kg/s
\(\dot m_a\) Commercial acid kg/s
\(\dot V_a\) Commercial acid volume m³/s

Method and standards

Stoichiometry.

Where it is used

  • Clarification chemical dosing.
  • Chemical cost reports.

Common mistakes

  • ppm on mass treated as mg/L without density.

Assumptions and limits

  • Uniform juice flow.
  • P₂O₅ concentrations are mg per litre of juice; ppm by mass is lower by the juice density (about 1.06).
  • The acid density is entered separately and must match the acid strength.

References

  • Stoichiometry P₂O₅ + 3 H₂O → 2 H₃PO₄ with IUPAC atomic masses

Questions and answers

Why phosphate?

Calcium phosphate flocs carry colloids and colour down in the clarifier.

How much P₂O₅ in juice?

Cane varies; mills dose to a target, often around 250–350 ppm. The page works in mg/L of juice; check whether a target is per litre, per kg of juice (juice density about 1.06) or on brix before entering it.

Why convert to H₃PO₄?

The acid bought is H₃PO₄; 1 kg P₂O₅ is about 1.38 kg H₃PO₄.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.