FireCADCalc

Strain Energy, Resilience and Suddenly Applied Load

Strain energy stored in a bar under axial load, the modulus of resilience and proof resilience, and the stress under a suddenly applied load.

Inputs

Examples: 50 kN on 500 mm², 2 m steel10 kN on 100 mm², 1 m aluminiumBolt: 80 kN on 245 mm², 80 mm, high-strength

Results

Stress P/A100.00MPa
Strain energy σ² A L/(2E)7.1429J
Modulus of resilience S_y²/(2E)285.71kJ/m³
Proof resilience of the bar28.571J
Stress if the load is applied suddenly 2P/A200.00MPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 50 kN on 500 mm², 2 m steel. The inputs, in the units selected above:

InputValue
Axial load (gradually applied)50.000 kN
Cross-sectional area500.00 mm²
Length2.0000 m
Young's modulus200.00 GPa
Yield (elastic limit) stress250.00 MPa

Applying the formula below gives:

ResultValue
Stress P/A100.00 MPa
Strain energy σ² A L/(2E)25.000 J
Modulus of resilience S_y²/(2E)156.25 kJ/m³
Proof resilience of the bar156.25 J
Stress if the load is applied suddenly 2P/A200.00 MPa

Open this example in the calculator and change any input.

Formula

\(U = \frac{\sigma^2}{2E} A L, \quad u_r = \frac{S_y^2}{2E}, \quad \sigma_{sudden} = \frac{2P}{A}\)

Variables

Symbol Meaning SI unit
\(P\) Axial load (gradually applied) N
\(A\) Cross-sectional area m²
\(L\) Length m
\(E\) Young's modulus Pa
\(S_y\) Yield (elastic limit) stress Pa
\(\sigma\) Stress P/A Pa
\(U\) Strain energy σ² A L/(2E) J
\(u_r\) Modulus of resilience S_y²/(2E) J/m³
\(U_p\) Proof resilience of the bar J
\(\sigma_s\) Stress if the load is applied suddenly 2P/A Pa

Method and standards

Elastic energy of an axially loaded bar.

Where it is used

  • Bolts and studs under shock.
  • Strength of materials examinations.

Common mistakes

  • Using ultimate strength for resilience.
  • Forgetting the factor 2 for sudden loads.

Assumptions and limits

  • Elastic, uniform bar: the page warns when P/A, or 2P/A for a sudden load, exceeds the yield stress.
  • The modulus of resilience is shown in kJ/m³ in every unit system.

References

  • Textbook mechanics (strain energy, Timoshenko, Strength of Materials)

Questions and answers

50 kN on a 500 mm², 2 m steel bar?

Stress 100 MPa; strain energy 25 J.

What is proof resilience?

The most energy the bar can store elastically: the modulus of resilience times its volume.

Why double for a sudden load?

The load does work over the whole deflection before the bar pushes back fully.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.