FireCADCalc

Shaft Angle of Twist and Torsional Shear Stress

Angle of twist, maximum shear stress, polar moment of area and torsional stiffness of a solid or hollow circular shaft under torque, by elastic torsion theory.

PumpFan and blower

Inputs

Examples: 2 kN·m, 2 m, 60 mm solid steel10 kN·m, 3 m, 120 / 80 mm hollow500 N·m, 1 m, 40 mm aluminium (26 GPa)

About 80 GPa for carbon steel; use your material's value.

Results

Elastic torsion of a straight circular shaft; keyways and shoulders raise the stress locally.

Polar moment of area π(D⁴ − d⁴)/3225.133cm⁴
Angle of twist T L / (G J)4.3841°
Maximum shear stress T (D/2) / J39.789MPa
Torsional stiffness G J / L (torque per radian)6,534.5N·m
Twist per metre of length (per m in every unit system)4.3841°

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 2 kN·m, 2 m, 60 mm solid steel. The inputs, in the units selected above:

InputValue
Torque2,000.0 N·m
Shaft length2.0000 m
Outside diameter60.000 mm
Inside diameter (0 for a solid shaft)0 mm
Shear modulus of the material80.000 GPa

Applying the formula below gives:

ResultValue
Polar moment of area π(D⁴ − d⁴)/32127.23 cm⁴
Angle of twist T L / (G J)2.2516 °
Maximum shear stress T (D/2) / J47.157 MPa
Torsional stiffness G J / L (torque per radian)50,894 N·m
Twist per metre of length (per m in every unit system)1.1258 °

Open this example in the calculator and change any input.

Formula

\(J = \frac{\pi (D^4 - d^4)}{32}, \quad \theta = \frac{T L}{G J}, \quad \tau_{max} = \frac{T\, D/2}{J}\)

Variables

Symbol Meaning SI unit
\(T\) Torque N·m
\(L\) Shaft length m
\(D\) Outside diameter m
\(d\) Inside diameter (0 for a solid shaft) m
\(G\) Shear modulus of the material Pa
\(J\) Polar moment of area π(D⁴ − d⁴)/32 m⁴
\(\theta\) Angle of twist T L / (G J) rad
\(\tau_{max}\) Maximum shear stress T (D/2) / J Pa
\(k_t\) Torsional stiffness G J / L (torque per radian) N·m
\(\theta/L\) Twist per metre of length rad/m

Method and standards

Torsion equation for straight circular shafts.

Where it is used

  • Line shafts and long drives.
  • Coupling alignment.
  • Strength of materials examinations.

Common mistakes

  • Using I instead of J.
  • Degrees and radians mixed.

Assumptions and limits

  • Elastic, circular, uniform shaft.
  • The twist per length is always given per metre, also when lengths are shown in feet (multiply by 0.3048 for per foot).

References

  • Elastic torsion of circular shafts (T/J = τ/r = Gθ/L)

Questions and answers

How much does a 60 mm steel shaft twist under 2 kN·m over 2 m?

0.0393 rad = 2.25°, with a maximum shear stress of 47.2 MPa.

Why are hollow shafts used?

Most torque is carried near the surface; a 120/80 mm tube has 80 % of the solid stiffness at 56 % of the weight.

What shear modulus for steel?

About 80 GPa; use your material's value.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.