FireCADCalc

Duct Pressure Drop (Air and Flue Gas)

Pressure drop of a round or rectangular air or flue gas duct by Darcy–Weisbach with the Colebrook friction factor on the hydraulic diameter, plus fittings.

Thermic fluid heatingStack and chimneyFan and blower

Inputs

Examples: Round duct 800 mm, 8 m³/s air, 60 m, K 1.5Rectangular 1 600 x 1 000 mm, 20 m³/s air, 40 m, K 2Flue duct 2 000 x 1 600 mm, 45 m³/s gas 140 °C, 35 m, K 3

Air 1.85 × 10⁻⁵ Pa·s at 30 °C; flue gas about 2.3 × 10⁻⁵ at 140 °C (gas properties calculator).
Galvanised sheet about 0.15 mm (ASHRAE); plain steel plate with some scale 0.5 mm or more.
Bends, dampers, transitions, entry and exit, each on the duct velocity pressure.

Round

Rectangular

Results

Total pressure drop22.430mmWC
Friction in straight duct4.1068mmWC
Loss in fittings18.323mmWC
Velocity12.500m/s
Velocity pressure9.1615mmWC
Reynolds number956,341
Darcy friction factor0.013793
Hydraulic diameter1,230.8mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Round duct 800 mm, 8 m³/s air, 60 m, K 1.5. The inputs, in the units selected above:

InputValue
Duct shapeRound
Inside diameter (round)800.00 mm
Inside width (rectangular)0 mm
Inside height (rectangular)0 mm
Duct length60.000 m
Volume flow (actual)28,800 m³/h
Gas density1.1500 kg/m³
Dynamic viscosity1.8500e-05 Pa·s
Wall roughness0.15000 mm
Sum of fitting loss coefficients1.5000 -

Applying the formula below gives:

ResultValue
Total pressure drop38.725 mmWC
Friction in straight duct16.447 mmWC
Loss in fittings22.278 mmWC
Velocity15.915 m/s
Velocity pressure14.852 mmWC
Reynolds number791,473
Darcy friction factor0.014765
Hydraulic diameter800.00 mm

Open this example in the calculator and change any input.

Formula

\(D_h = D\ \text{(round)},\ \ \frac{2ab}{a+b}\ \text{(rectangular)} \qquad v = \frac{\dot V}{A} \qquad Re = \frac{\rho\,v\,D_h}{\mu} \qquad p_d = \frac{\rho v^2}{2}\)

\(\frac{1}{\sqrt f} = -2\log_{10}\!\left(\frac{\varepsilon/D_h}{3.7} + \frac{2.51}{Re\sqrt f}\right) \qquad \Delta p_f = f\,\frac{L}{D_h}\,p_d \qquad \Delta p_K = \Sigma K\,p_d \qquad \Delta p = \Delta p_f + \Delta p_K\)

Variables

Symbol Meaning SI unit
\(\text{shape}\) round or rectangular –
\(D\) inside diameter, round duct m
\(a\) inside width, rectangular duct m
\(b\) inside height, rectangular duct m
\(L\) duct length m
\(\dot V\) actual volume flow m³/s
\(\rho\) gas density kg/m³
\(\mu\) dynamic viscosity Pa·s
\(\varepsilon\) wall roughness m
\(\Sigma K\) sum of fitting loss coefficients –
\(\Delta p\) total pressure drop Pa
\(\Delta p_f\) friction in straight duct Pa
\(\Delta p_K\) loss in fittings Pa
\(v\) velocity m/s
\(p_d\) velocity pressure Pa
\(Re\) Reynolds number –
\(f\) Darcy friction factor –
\(D_h\) hydraulic diameter m
\(A\) flow area m²

Method and standards

Darcy–Weisbach with the Colebrook–White friction factor (laminar 64/Re), on the hydraulic diameter, as in the Duct Design chapter of the ASHRAE Handbook—Fundamentals. Fittings by loss coefficients on the duct velocity pressure.

Where it is used

  • Sizing air and flue gas ducts.
  • Estimating fan pressure.
  • Checking duct modifications.

Common mistakes

  • Using standard air density for hot gas.
  • Forgetting bends, dampers and transitions.
  • Using hydraulic diameter wrongly for rectangular ducts.

Assumptions and limits

  • Constant density along the duct (pressure changes small against absolute pressure).
  • Fully developed turbulent flow; loss coefficients of fittings close together interact and are approximate.
  • Laminar 64/Re below Re 2 300, Colebrook above; the transitional range 2 300–4 000 (Colebrook, conservative) is flagged.
  • For flat ducts (aspect ratio above about 4) the hydraulic-diameter method slightly underestimates friction.

References

  • Darcy–Weisbach equation
  • Colebrook (1939)
  • ASHRAE Handbook—Fundamentals (2017)
  • ch. 21 (Duct Design)

Questions and answers

How is duct pressure drop calculated?

Δp = (f·L/D_h + ΣK)·ρv²/2, with f from Colebrook at the duct's Reynolds number and relative roughness. 20 m³/s of air in a 1 600 × 1 000 mm duct over 40 m with ΣK = 2 loses 220 Pa, most of it in the fittings.

Hydraulic or equivalent diameter?

This calculator uses the hydraulic diameter with the true velocity in the duct, which gives the same friction as Huebscher's equivalent diameter with the volume flow.

What roughness should I use?

About 0.15 mm for galvanised sheet ducts (ASHRAE); plain steel plate ducts with scale or ash deposits are rougher, often 0.5 mm or more.

Method and article reviewed by FireCAD engineering on 10 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.