Worked example
Example: Fast CO2–amine-like. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Second-order rate constant (m³/(kmol·s)) | 5,000.0 - |
| Liquid-phase reactant concentration (kmol/m³) | 0.50000 - |
| Diffusivity of the dissolved gas in the liquid | 1.8000e-09 m²/s |
| Liquid-side mass-transfer coefficient | 1.0000e-04 m/s |
| Interface concentration of the gas (kmol/m³) | 0.020000 - |
| Diffusivity of the liquid reactant (0 if unknown) | 0 m²/s |
| Moles of liquid reactant per mole of gas absorbed | 1.0000 - |
Applying the formula below gives:
| Result | Value |
|---|---|
| Hatta number | 21.213 |
| Enhancement factor | 21.213 |
| Regime (1 slow, 2 intermediate, 3 fast) | 3.0000 |
| Absorption flux (kmol/(m²·s)) | 4.2426e-05 |
Open this example in the calculator and change any input.
Formula
\(Ha = \frac{\sqrt{k_2C_BD_A}}{k_L}, \quad E = \min\left(\frac{Ha}{\tanh Ha},\ E_i\right), \quad E_i = 1 + \frac{D_BC_B}{\nu D_AC_{Ai}}, \quad N_A = Ek_LC_{Ai}\)
Regime: slow for \(Ha < 0.3\), intermediate for \(0.3 \le Ha \le 3\), fast for \(Ha > 3\).
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(k_2\) | Second-order rate constant (m³/(kmol·s)) | - |
| \(C_B\) | Liquid-phase reactant concentration (kmol/m³) | - |
| \(D_A\) | Diffusivity of the dissolved gas in the liquid | m²/s |
| \(k_L\) | Liquid-side mass-transfer coefficient | m/s |
| \(C_{Ai}\) | Interface concentration of the gas (kmol/m³) | - |
| \(Ha\) | Hatta number | - |
| \(E\) | Enhancement factor | - |
| \(\text{regime}\) | Regime (1 slow, 2 intermediate, 3 fast) | - |
| \(N_A\) | Absorption flux (kmol/(m²·s)) | - |
| \(D_B\) | Diffusivity of the liquid reactant (0 if unknown) | m²/s |
| \(\nu\) | Moles of liquid reactant per mole of gas absorbed | - |
| \(E_i\) | Instantaneous-reaction enhancement | - |
Method and standards
Film theory, pseudo-first order.
Where it is used
- Amine and caustic scrubbers.
- Gas–liquid reactor selection.
Common mistakes
- Ignoring reactant depletion (instantaneous regime).
- Using gas-side k_G for k_L.
Assumptions and limits
- Pseudo-first order; film theory.
- Without D_B the instantaneous limit is not applied and E can be overstated at high Ha. With D_B entered, E is limited to E_i, and a note warns when Ha exceeds E_i/2, where reactant depletion makes the pseudo-first-order value too high.
References
- Levenspiel
- Chemical Reaction Engineering
- 3rd ed. (Wiley, 1999)
- ch. 23 (fluid–fluid reactions: Hatta number and enhancement factor)
- Perry's Chemical Engineers' Handbook
- 9th ed. (McGraw-Hill, 2019)
- sec. 14 (absorption with chemical reaction)
Questions and answers
What does the Hatta number mean?
Reaction rate in the liquid film against diffusion through it: below 0.3 the reaction happens in the bulk; above 3 within the film, and absorption speeds up.
Why does it matter for design?
In the fast regime the interfacial area governs, so packing or spray area matters; in the slow regime liquid holdup does.
What do the defaults represent?
CO₂ into an amine-like solution with a fast second-order reaction.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.