FireCADCalc

Energy of a Pressure Vessel Burst (Brode, Isentropic, Isothermal)

Energy released when a gas-filled vessel bursts, by Brode's equation, isentropic and isothermal expansion and thermodynamic availability, and its TNT equivalent.

Process steam and utilitiesDistillery and ethanolRefinery and petrochemicalChemical and fertiliserTank and drumAir compressor and receiver

Inputs

Examples: 1 m³ air at 500 psiaNitrogen receiver 5 m³ at 10 barCO2 bottle 0.05 m³ at 60 bar

Results

Ideal gas at ambient temperature. Brode is thought best for near-field blast and isentropic expansion for the far field; part of the energy goes into fragments, so about half is often used for blast effects. Liquids store far less energy; a vessel that bursts with liquid above its boiling point can BLEVE.

A screening estimate for training and early design, not a hazard or risk study.

Brode's equation12,483kJ
Isentropic expansion6,793.4kJ
Isothermal expansion13,116kJ
Thermodynamic availability8,122.7kJ
TNT equivalent of Brode's energy2.6640kg

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1 m³ air at 500 psia. The inputs, in the units selected above:

InputValue
Gas volume in the vessel1.0000 m³
Burst pressure (absolute)3,447.4 kPa
Ambient pressure101.33 kPa
Heat capacity ratio of the gas1.4000 -

Applying the formula below gives:

ResultValue
Brode's equation8,365.1 kJ
Isentropic expansion5,472.3 kJ
Isothermal expansion12,159 kJ
Thermodynamic availability8,813.0 kJ
TNT equivalent of Brode's energy1.7851 kg

Open this example in the calculator and change any input.

Formula

\(E_{Brode} = \frac{(P_2 - P_1)V}{\gamma - 1}, \quad E_{isentropic} = \frac{P_2V}{\gamma - 1}\left[1 - \left(\frac{P_1}{P_2}\right)^{(\gamma - 1)/\gamma}\right]\)

\(E_{isothermal} = P_2V\ln\frac{P_2}{P_1}, \quad E_{avail} = P_2V\left[\ln\frac{P_2}{P_1} - \left(1 - \frac{P_1}{P_2}\right)\right]\)

Variables

Symbol Meaning SI unit
\(V\) Gas volume in the vessel m³
\(P_2\) Burst pressure (absolute) Pa
\(P_1\) Ambient pressure Pa
\(\gamma\) Heat capacity ratio of the gas -
\(E_{Brode}\) Brode's equation J
\(E_{isentropic}\) Isentropic expansion J
\(E_{isothermal}\) Isothermal expansion J
\(E_{avail}\) Thermodynamic availability J
\(m_{TNT}\) TNT equivalent of Brode's energy kg

Method and standards

Energy of explosion for a compressed ideal gas by the four methods given by Crowl and Louvar; TNT equivalent at 4,686 kJ/kg.

Where it is used

  • Pneumatic test safety distances (screening).
  • Gas receivers and accumulators.

Common mistakes

  • Using gauge pressure.
  • Forgetting the gas volume excludes internals.

Assumptions and limits

  • Ideal gas; ambient temperature.

References

  • Crowl and Louvar
  • Chemical Process Safety: Fundamentals with Applications
  • 2nd ed. (Prentice Hall, 2002)
  • ch. 6
  • eqs. 6-28 to 6-31 (Brode; Crowl, thermodynamic availability)

Questions and answers

Why are hydrotests preferred to pneumatic tests?

Water is nearly incompressible and stores very little energy; the same vessel full of gas at test pressure stores thousands of times more.

Which method should I use?

All four are in use: isothermal gives the largest value and isentropic the smallest; Brode is common for near-field effects.

What do the defaults represent?

A 1 m³ vessel of air bursting at 500 psia into 1 atm.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.