FireCADCalc

Inerting by Pressure or Sweep Purging: Cycles and Nitrogen

Oxygen left after nitrogen pressure-purge cycles, cycles needed for a target, nitrogen used, and the sweep-through purge volume for the same target.

Distillery and ethanolRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 10 m³, air to 6 % O2, 1 to 5 bar(a)2 m³, to 1 % O2, 1 to 8 bar(a)

Results

Ideal mixing assumed; dead legs and poor mixing need more nitrogen. Verify with an oxygen analyser. Pure nitrogen assumed: impure or PSA nitrogen leaves an oxygen floor at its own O₂ content. Screening estimate only, not a safety study or a basis for protective design.

Pressure cycles needed2.0000
Oxygen after those cycles0.33688%
Nitrogen for the pressure purge32.121kg
Nitrogen volume for a sweep purge (at vessel conditions)6.0890m³

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 10 m³, air to 6 % O2, 1 to 5 bar(a). The inputs, in the units selected above:

InputValue
Vessel volume10.000 m³
Initial oxygen21.000 %
Target oxygen6.0000 %
Low pressure of the cycle (absolute)1.0132 bar
High pressure of the cycle (absolute)5.0000 bar
Temperature25.000 °C

Applying the formula below gives:

ResultValue
Pressure cycles needed1.0000
Oxygen after those cycles4.2556 %
Nitrogen for the pressure purge45.053 kg
Nitrogen volume for a sweep purge (at vessel conditions)12.528 m³

Open this example in the calculator and change any input.

Formula

\(y_j = y_0\left(\frac{p_L}{p_H}\right)^j, \quad m_{N_2} = j\frac{(p_H - p_L)V}{RT}M_{N_2}, \quad Qt = V\ln\frac{y_0}{y_t}\)

Variables

Symbol Meaning SI unit
\(V\) Vessel volume m³
\(y_0\) Initial oxygen -
\(y_t\) Target oxygen -
\(p_L\) Low pressure of the cycle (absolute) Pa
\(p_H\) High pressure of the cycle (absolute) Pa
\(T\) Temperature K
\(j\) Pressure cycles needed -
\(y_j\) Oxygen after those cycles -
\(m_{N_2}\) Nitrogen for the pressure purge kg
\(Q t\) Nitrogen volume for a sweep purge (at vessel conditions) m³

Method and standards

Ideal-mixing purge relations.

Where it is used

  • Start-up and shutdown inerting procedures.

Common mistakes

  • Ignoring dead legs.
  • Using gauge pressures.

Assumptions and limits

  • Ideal gas; perfect mixing; pure nitrogen. Impure nitrogen (99 % or PSA 97 %) carries its own oxygen, which sets a floor on the oxygen reached; more cycles are then needed, or the target cannot be met.

References

  • Purging by ideal mixing (definitions; see Perry's sec. 23 on inerting)

Questions and answers

Why does each cycle multiply by p_L/p_H?

Pressurising with pure nitrogen dilutes the oxygen by that ratio; venting back keeps the same fraction.

Which uses less nitrogen?

Pressure purging with a large pressure ratio usually does, for vessels that can take the pressure.

Why ln(y₀/y) volumes for a sweep?

With perfect mixing the oxygen falls exponentially with the volumes swept through.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.