FireCADCalc

Deflagration Index K_G or K_St (Cubic Law)

Deflagration index from the maximum rate of pressure rise in a test vessel and its volume (K = (dP/dt)max·V^⅓), and the rate expected in another closed vessel.

Thermal power plantRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: Dust in 20 L sphere, 600 bar/s, to 10 m³Gas in 1 m³, 100 bar/s, to 50 m³

bar/s

Results

The cubic law needs geometrically similar vessels and the same turbulence. Vent sizing follows NFPA 68 or EN 14491, not this calculator. Screening estimate only, not a safety study or a basis for protective design.

St classes apply to dusts only; for a gas K is K_G and the class has no meaning. Class St 0 (no explosion) is found by test, not from a K above zero.

Deflagration index (bar·m/s)100.00
Expected max rate in V₂ (bar/s)27.144
Dust class St by K_St (dusts only; 1: ≤200, 2: ≤300, 3: >300)1.0000

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Dust in 20 L sphere, 600 bar/s, to 10 m³. The inputs, in the units selected above:

InputValue
Maximum rate of pressure rise in the test600.00 -
Test vessel volume20.000 L
Volume of the vessel of interest10.000 m³

Applying the formula below gives:

ResultValue
Deflagration index (bar·m/s)162.87
Expected max rate in V₂ (bar/s)75.595
Dust class St by K_St (dusts only; 1: ≤200, 2: ≤300, 3: >300)1.0000

Open this example in the calculator and change any input.

Formula

\(K = \left(\frac{dP}{dt}\right)_{max}V^{1/3}, \quad \left(\frac{dP}{dt}\right)_2 = \frac{K}{V_2^{1/3}}\)

Variables

Symbol Meaning SI unit
\((dP/dt)_{max}\) Maximum rate of pressure rise in the test -
\(V\) Test vessel volume m³
\(V_2\) Volume of the vessel of interest m³
\(K\) Deflagration index (bar·m/s) -
\((dP/dt)_2\) Expected max rate in V₂ (bar/s) -
\(St\) Dust class St by K_St (dusts only; 1: ≤200, 2: ≤300, 3: >300) -

Method and standards

Cubic law.

Where it is used

  • Comparing dust and gas explosion severity.

Common mistakes

  • Using it for vent sizing.
  • Comparing tests from different vessel sizes or ignition energies.

Assumptions and limits

  • Similar geometry and turbulence.
  • The St class is for dusts; it is shown for any K but has no meaning for a gas K_G. St 0 (no explosion) comes from a test that shows no explosion, so it never results from a positive rate here.

References

  • Perry's Chemical Engineers' Handbook
  • 9th ed. (McGraw-Hill, 2019)
  • sec. 23 (deflagration index K_G, K_St = (dP/dt)max V^⅓; dust explosion classes)

Questions and answers

What is K_St?

The maximum rate of pressure rise normalised by vessel size; it ranks how violently a dust explodes.

What are the dust classes?

St 1 up to 200, St 2 up to 300, St 3 above 300 bar·m/s.

Why does a bigger vessel see a slower rise?

The flame takes longer to cross it: dP/dt falls as V^−⅓.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.