FireCADCalc

Bubble-Point Pressure and Oil Formation Volume Factor (Standing)

Bubble-point pressure and oil formation volume factor of a crude from solution gas-oil ratio, gas gravity, API gravity and temperature by Standing's correlations.

Process steam and utilitiesRefinery and petrochemicalChemical and fertiliser

Inputs

Examples: 30 °API, 350 scf/STB, 200 °FAhmed Example 2-24, oil 1 (p_b 2,181 psia)Heavy oil, 120 scf/STB

Results

Standing's correlations come from California crudes; use them with caution when the gas holds much CO₂, N₂ or H₂S. Temperatures in °F are taken as T(°R) − 460, as in Ahmed's equations.

Bubble-point pressure1,890.3psi
Oil formation volume factor at the bubble point1.2212
Oil specific gravity0.87616

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 30 °API, 350 scf/STB, 200 °F. The inputs, in the units selected above:

InputValue
Solution gas-oil ratio at the bubble point350.00 scf/STB
Solution gas gravity (air = 1)0.75000 -
Oil gravity30.000 -
Reservoir temperature93.517 °C

Applying the formula below gives:

ResultValue
Bubble-point pressure1,890.3 psi
Oil formation volume factor at the bubble point1.2212
Oil specific gravity0.87616

Open this example in the calculator and change any input.

Formula

\(p_b = 18.2\left[\left(\frac{R_s}{\gamma_g}\right)^{0.83}10^{a} - 1.4\right], \quad a = 0.00091(T - 460) - 0.0125\,\text{API}\)

\(B_o = 0.9759 + 0.000120\left[R_s\left(\frac{\gamma_g}{\gamma_o}\right)^{0.5} + 1.25(T - 460)\right]^{1.2}\)

Variables

Symbol Meaning SI unit
\(R_s\) Solution gas-oil ratio at the bubble point m³/m³
\(\gamma_g\) Solution gas gravity (air = 1) -
\(\text{API}\) Oil gravity -
\(T\) Reservoir temperature K
\(p_b\) Bubble-point pressure Pa
\(B_{ob}\) Oil formation volume factor at the bubble point -
\(\gamma_o\) Oil specific gravity -

Method and standards

Standing's correlations in field units (psia, scf/STB, °R).

Where it is used

  • Reservoir fluid screening without a PVT report.
  • Well and facility design.

Common mistakes

  • Using separator gas gravity without adjustment.
  • Applying to volatile oils.

Assumptions and limits

  • Black oil; hydrocarbon gas.

References

  • Ahmed
  • Reservoir Engineering Handbook
  • 5th ed. (Gulf Professional Publishing, 2019)
  • ch. 2
  • eqs. 2-76
  • 2-77 and 2-84 (Standing, 1981)

Questions and answers

What is the bubble point?

The pressure at which the first gas bubble leaves the oil; above it the oil is undersaturated.

How accurate is Standing's correlation?

Typically within about 5 % for the crudes it was built on; check with a laboratory PVT report when one exists.

What do the defaults represent?

A 30 °API oil with 350 scf/STB of 0.75-gravity gas at 200 °F.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.