FireCADCalc

Gas Velocity in a Pipeline and Erosional Velocity

Actual gas velocity at a pressure and temperature from the flow at base conditions, the erosional velocity limit C/√ρ, and the ratio between them.

Thermal power plantProcess steam and utilitiesRefinery and petrochemicalChemical and fertiliserFuel oil and gas system

Inputs

Examples: Menon Example 1: 250 MMSCFD, NPS 20, 1000 psigPlant header at 6 bar, 150 mmWet gas, C = 80

Results

Menon recommends operating at no more than about half the erosional velocity. The constant C = 100 (US customary units) is the usual value for continuous service in clean gas; solids or liquids call for a lower velocity.

Gas density at flowing conditions56.279kg/m³
Gas velocity5.8499m/s
Erosional velocity16.261m/s
Velocity as a share of erosional35.974%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Menon Example 1: 250 MMSCFD, NPS 20, 1000 psig. The inputs, in the units selected above:

InputValue
Gas flow at base conditions7,079,212 m³/d
Gas pressure (absolute)6,996.1 kPa
Gas temperature15.556 °C
Compressibility factor0.90000 -
Gas gravity (air = 1)0.60000 -
Pipe inside diameter482.60 mm
Erosional constant (US customary, 100 for continuous service)100.00 -
Base temperature15.556 °C
Base pressure101.35 kPa

Applying the formula below gives:

ResultValue
Gas density at flowing conditions56.279 kg/m³
Gas velocity5.8402 m/s
Erosional velocity16.261 m/s
Velocity as a share of erosional35.915 %

Open this example in the calculator and change any input.

Formula

\(\rho = \frac{P\,G\,M_{air}}{ZRT}, \quad u = \frac{Q_b}{A}\frac{P_b}{P}\frac{T}{T_b}Z, \quad u_{max} = \frac{C}{\sqrt{\rho}}\ (\text{ft/s},\ \rho\ \text{in lb/ft}^3)\)

Variables

Symbol Meaning SI unit
\(Q_b\) Gas flow at base conditions m³/s
\(P\) Gas pressure (absolute) Pa
\(T\) Gas temperature K
\(Z\) Compressibility factor -
\(G\) Gas gravity (air = 1) -
\(D\) Pipe inside diameter m
\(C\) Erosional constant (US customary, 100 for continuous service) -
\(T_b\) Base temperature K
\(P_b\) Base pressure Pa
\(\rho\) Gas density at flowing conditions kg/m³
\(u\) Gas velocity m/s
\(u_{max}\) Erosional velocity m/s
\(u/u_{max}\) Velocity as a share of erosional -

Method and standards

Gas law and the erosional velocity relation as given by Menon (C = 100). Air molar mass 28.9647 kg/kmol.

Where it is used

  • Line sizing and checking velocity at the delivery end.
  • Station piping and headers.

Common mistakes

  • Using the base-condition flow as the actual flow.
  • Applying C = 100 to sandy or wet gas.

Assumptions and limits

  • Z = 1 at base conditions; ideal mixing rule for gravity.

References

  • Menon
  • Gas Pipeline Hydraulics (CRC Press, 2005)
  • ch. 2
  • eqs. 2.24–2.31

Questions and answers

Why is the velocity highest at the outlet?

Pressure falls along the line, so the same mass of gas takes more volume and moves faster.

What velocity is acceptable?

Up to about half the erosional velocity; in practice 10–20 m/s in transmission lines.

What do the defaults represent?

Menon's Example 1: 250 MMSCFD (7.08 million m³/day) in a 19-inch bore line at 1,000 psig and 60 °F, Z = 0.9.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.