FireCADCalc

Wort Boiling: Evaporation and Steam

Water evaporated in the brewhouse wort kettle from the evaporation rate and boil time, the heat to bring wort to the boil and evaporate, and the steam.

Food, dairy and textileIAPWS-IF97 (water and steam)

Inputs

Examples: 100 m3 wort, 6 %/h, 60 minSmall brewhouse 20 m3, 8 %/h, 90 min

Results

Modern low-evaporation kettles (4–6 % per hour) with vapour condensers recover much of the boil heat.

Water evaporated2.4960t
Heat (heat-up + evaporation)7.6021GJ
Steam3.5139t

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 100 m3 wort, 6 %/h, 60 min. The inputs, in the units selected above:

InputValue
Wort volume100.00 m³
Wort density1,040.0 kg/m³
Wort specific heat3.9500 kJ/(kg·K)
Wort temperature into the kettle72.000 °C
Evaporation per hour (share of the wort mass)6.0000 %
Boil time60.000 min
Steam pressure (absolute)4.0000 bar

Applying the formula below gives:

ResultValue
Water evaporated6.2400 t
Heat (heat-up + evaporation)25.573 GJ
Steam11.987 t

Open this example in the calculator and change any input.

Formula

\(E = V\rho\,e\,t_b, \quad Q = V\rho c_p(T_b - T_1) + E\,h_{fg}\)

Variables

Symbol Meaning SI unit
\(V\) Wort volume m³
\(\rho\) Wort density kg/m³
\(c_p\) Wort specific heat J/(kg·K)
\(T_1\) Wort temperature into the kettle K
\(e\) Evaporation per hour (share of the wort mass) -
\(t_b\) Boil time s
\(p_s\) Steam pressure (absolute) Pa
\(E\) Water evaporated kg
\(Q\) Heat (heat-up + evaporation) J
\(m_s\) Steam kg

Method and standards

Heat-up and evaporation balance.

Where it is used

  • Brewhouse steam budgets.

Common mistakes

  • Using total evaporation per brew as per hour.

Assumptions and limits

  • Atmospheric boiling at sea level (1 atm), whatever the site altitude; no kettle heat losses or heating-surface inefficiency, so the steam is a minimum.
  • The evaporation rate is a share of the wort mass (V ρ) per hour. A rate quoted as a share of hot wort volume gives a water mass about 4 % lower (water is less dense than wort).

References

  • Mass and energy balances (definitions)
  • Steam and water properties from IAPWS-IF97

Questions and answers

What evaporation rate is usual?

4–8 % of the volume per hour; older kettles 8–10 %.

Why boil at all?

Sterilisation, hop isomerisation, protein coagulation and driving off DMS.

Is the boiling point 100 °C?

About 100 °C at sea level; the calculator uses water at 1 atm.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.