FireCADCalc

Retort or Blancher Steam: Product Heating Load

Steam to heat a batch of product and containers (or a blancher feed) from initial to process temperature, with the vessel's own heat and losses, by IF97 latent heat.

Food, dairy and textileIAPWS-IF97 (water and steam)Boiler

Inputs

Examples: 2 t product + 1.5 t steel to 121 °CBlancher 1 t veg to 95 °C

Results

Venting air at the start of a steam retort uses a lot of extra steam; it is part of the loss share here.

Latent heat only: with steam injected into retort water the condensate's sensible heat is also used (the steam here is conservative), and the retort water must be added to the heated masses.

Heat required361.79MJ
Steam164.33kg
Average steam rate during come-up657.33kg/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 2 t product + 1.5 t steel to 121 °C. The inputs, in the units selected above:

InputValue
Product2,000.0 kg
Product specific heat3.7000 kJ/(kg·K)
Containers, crates and vessel steel1,500.0 kg
Their specific heat0.48000 kJ/(kg·K)
Initial temperature20.000 °C
Process temperature121.00 °C
Steam pressure (absolute)4.0000 bar
Losses and venting share15.000 %
Come-up time15.000 min

Applying the formula below gives:

ResultValue
Heat required964.85 MJ
Steam452.27 kg
Average steam rate during come-up1,809.1 kg/h

Open this example in the calculator and change any input.

Formula

\(Q = \frac{(M_pc_p + M_cc_c)(T_2 - T_1)}{1 - \varepsilon}, \quad m_s = \frac{Q}{h_{fg}(p_s)}\)

Variables

Symbol Meaning SI unit
\(M_p\) Product kg
\(c_p\) Product specific heat J/(kg·K)
\(M_c\) Containers, crates and vessel steel kg
\(c_c\) Their specific heat J/(kg·K)
\(T_1\) Initial temperature K
\(T_2\) Process temperature K
\(p_s\) Steam pressure (absolute) Pa
\(\varepsilon\) Losses and venting share -
\(t_u\) Come-up time s
\(Q\) Heat required J
\(m_s\) Steam kg
\(\dot m_s\) Average steam rate during come-up kg/s

Method and standards

Sensible heat balance with IF97 latent heat.

Where it is used

  • Retort and blancher steam supply sizing.

Common mistakes

  • Ignoring venting steam.
  • Using product mass only.

Assumptions and limits

  • Uniform final temperature.
  • Only the latent heat of the steam is counted. In water-immersion or water-spray retorts and blanchers with steam injection, the condensate mixes with the water and also gives up sensible heat, so the steam here is on the safe side. The retort water itself and its heating are not included: add it to the containers term.

References

  • Mass and energy balances (definitions)
  • Steam and water properties from IAPWS-IF97

Questions and answers

Why count the containers?

Cans, glass and crates must be heated too; glass and steel can be a large share.

Why is peak steam higher than average?

Most steam is drawn early, when the temperature difference is largest.

What about condensate?

It leaves at saturation; only latent heat is counted.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.