FireCADCalc

Ash Generation Rate (Bottom Ash and Fly Ash)

Bottom ash and fly ash produced by a boiler from the firing rate, ash content and unburned carbon in the residue, per hour and per year.

Thermal power plantSugar mill and cogenerationPulp and paperASME PTC 4 (fired steam generators)BoilerDust collector (ESP, bag filter, cyclone)

Inputs

Examples: Indian coal 50 t/h, 35 % ash, 2 % carbon in residue, 80 % fly ashBagasse 25 t/h, 1.25 % ash, 10 % carbon, 70 % flyImported coal 20 t/h, 12 % ash, 1 % carbon, 85 % fly

Set by the firing system: pulverised coal about 80 %, stokers and grates much less, fluidised beds in between. Use the boiler maker's split.

Results

Total residue (ash plus unburned carbon)17.857t/h
Fly ash14.286t/h
Bottom ash3.5714t/h
Residue per year142,857t
Unburned carbon in the residue357.14kg/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Indian coal 50 t/h, 35 % ash, 2 % carbon in residue, 80 % fly ash. The inputs, in the units selected above:

InputValue
Fuel firing rate50,000 kg/h
Ash in the fuel, as fired35.000 %
Carbon in the residue (unburned carbon)2.0000 %
Share of the residue leaving as fly ash80.000 %
Operating hours per year8,000.0 h

Applying the formula below gives:

ResultValue
Total residue (ash plus unburned carbon)17.857 t/h
Fly ash14.286 t/h
Bottom ash3.5714 t/h
Residue per year142,857 t
Unburned carbon in the residue357.14 kg/h

Open this example in the calculator and change any input.

Formula

\(\dot m_r = \frac{\dot m_f\,A}{1 - c_r} \qquad \dot m_{fa} = x_f\,\dot m_r \qquad \dot m_{ba} = (1 - x_f)\,\dot m_r \qquad \dot m_c = c_r\,\dot m_r \qquad m_r = \dot m_r\,t_{op}\)

Variables

Symbol Meaning SI unit
\(\dot m_f\) fuel firing rate kg/s
\(A\) ash in the fuel as fired –
\(c_r\) carbon in the residue –
\(x_f\) share of the residue leaving as fly ash –
\(t_{op}\) operating hours per year s
\(\dot m_r\) total residue kg/s
\(\dot m_{fa}\) fly ash kg/s
\(\dot m_{ba}\) bottom ash kg/s
\(m_r\) residue per year kg
\(\dot m_c\) unburned carbon in the residue kg/s

Method and standards

Mass balance on the incombustible matter: all the fuel ash leaves as residue together with the unburned carbon, as in the residue terms of ASME PTC 4-2013.

Where it is used

  • Sizing ash handling systems, silos and ash ponds.
  • Planning fly ash sale to cement plants.
  • Comparing coals by the ash they leave.

Common mistakes

  • Forgetting unburned carbon, which adds to the ash mass.
  • Using the air-dried ash content with an as-fired coal flow.
  • Assuming one fly-ash share for every boiler type.

Assumptions and limits

  • Ash content as fired; limestone or sorbent added for desulphurisation adds to the residue (see the limestone calculator).
  • One carbon content for all residue streams; fly ash and bottom ash usually differ.
  • The fly-ash share splits the residue including its carbon, so with one carbon content it equals the split of the fuel ash.
  • The ash content must be on the as-fired basis of the firing rate; an air-dried or dry-basis ash with an as-fired rate overstates the residue.

References

  • Mass balance on fuel ash; ASME PTC 4-2013 (residue and unburned carbon)

Questions and answers

How much ash does a coal boiler produce?

Residue = fuel × ash ÷ (1 − carbon in residue). 50 t/h of 35 %-ash coal with 2 % carbon in the residue gives 17.9 t/h of ash, about 14.3 t/h as fly ash and 3.6 t/h as bottom ash with an 80/20 split.

Why does unburned carbon matter?

The residue is ash plus the carbon that did not burn, so a high carbon loss increases the ash to handle as well as costing efficiency.

Where does the fly-ash share come from?

From the firing system and the boiler maker; pulverised coal sends most ash to the fly ash, grates keep more as bottom ash.

Method and article reviewed by FireCAD engineering on 10 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.