Worked example
Example: High-ash Indian coal, 0.5 % S. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Silica SiO₂ | 58.000 % |
| Alumina Al₂O₃ | 27.000 % |
| Titania TiO₂ | 1.5000 % |
| Iron oxide Fe₂O₃ | 5.0000 % |
| Lime CaO | 2.0000 % |
| Magnesia MgO | 1.0000 % |
| Soda Na₂O | 0.30000 % |
| Potash K₂O | 1.2000 % |
| Sulphur in the coal, dry basis | 0.50000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Basic oxides Fe₂O₃ + CaO + MgO + Na₂O + K₂O | 9.5000 % |
| Acidic oxides SiO₂ + Al₂O₃ + TiO₂ | 86.500 % |
| Base-to-acid ratio | 0.10983 |
| Slagging index (B/A × % sulphur, dry) | 0.054913 |
| Fouling index (B/A × % Na₂O in ash) | 0.032948 |
Open this example in the calculator and change any input.
Formula
\(B = \text{Fe}_2\text{O}_3 + \text{CaO} + \text{MgO} + \text{Na}_2\text{O} + \text{K}_2\text{O}, \quad A = \text{SiO}_2 + \text{Al}_2\text{O}_3 + \text{TiO}_2\)
\(R_s = \frac{B}{A} \times S_d\,(\%), \quad R_f = \frac{B}{A} \times \text{Na}_2\text{O}\,(\%)\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\text{SiO}_2\) | Silica SiO₂ | - |
| \(\text{Al}_2\text{O}_3\) | Alumina Al₂O₃ | - |
| \(\text{TiO}_2\) | Titania TiO₂ | - |
| \(\text{Fe}_2\text{O}_3\) | Iron oxide Fe₂O₃ | - |
| \(\text{CaO}\) | Lime CaO | - |
| \(\text{MgO}\) | Magnesia MgO | - |
| \(\text{Na}_2\text{O}\) | Soda Na₂O | - |
| \(\text{K}_2\text{O}\) | Potash K₂O | - |
| \(S_d\) | Sulphur in the coal, dry basis | - |
| \(B\) | Basic oxides Fe₂O₃ + CaO + MgO + Na₂O + K₂O | - |
| \(A\) | Acidic oxides SiO₂ + Al₂O₃ + TiO₂ | - |
| \(B/A\) | Base-to-acid ratio | - |
| \(R_s\) | Slagging index (B/A × % sulphur, dry) | - |
| \(R_f\) | Fouling index (B/A × % Na₂O in ash) | - |
Method and standards
The indices of Attig and Duzy (1969, Proceedings of the American Power Conference) combine the fluxing basic oxides and the network-forming acidic oxides of the ash with sulphur (which travels with iron as pyrite) for slagging, and with sodium for convective-pass fouling. The oxides are percentages of the ash; sulphur is on the dry coal.
Where it is used
- Screening coals and blends for a pulverised coal or stoker boiler.
- Explaining slagging after a coal change.
- Setting soot-blowing priorities.
Common mistakes
- Using sulphur as received instead of dry.
- Applying the bituminous indices to lignitic ash (CaO + MgO above Fe₂O₃).
- Reading the bands as a guarantee: furnace temperature and design matter as much.
Assumptions and limits
- Bituminous-type ash; lignitic ash needs other indices (a warning appears when CaO + MgO exceeds Fe₂O₃, but the bituminous forms are still shown).
- An analysis whose oxides add up to less than 85 % gets a warning.
- Empirical bands; ash fusion temperatures should be checked too.
References
- Attig and Duzy (1969)
- Coal ash deposition studies and application to boiler design
- Proceedings of the American Power Conference vol. 31
- Babcock & Wilcox
- Steam (ash indices)
Questions and answers
How is the slagging index worked out?
Add the basic oxides (Fe₂O₃, CaO, MgO, Na₂O, K₂O) and the acidic ones (SiO₂, Al₂O₃, TiO₂); their ratio times the dry sulphur in per cent is Rs. An iron-rich ash with 2.5 % sulphur gives Rs 0.97, a medium tendency.
Why do Indian coals rarely slag on this index?
Their ash is mostly silica and alumina, so the base-to-acid ratio is about 0.1 and the sulphur is low: Rs about 0.05. Their problems are erosion and the large ash quantity instead.
What bands are used?
Attig and Duzy give Rs below 0.6 low, 0.6 to 2.0 medium, above 2.0 up to 2.6 high and above 2.6 severe; Rf below 0.2 low, 0.2 to 0.5 medium, above 0.5 up to 1.0 high and above 1.0 severe. A value exactly on a boundary takes the lower band.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.