FireCADCalc

Ash Fusion Temperature from Ash Analysis

Quick estimate of the ash melting temperature of a coal from its oxide analysis (Al₂O₃, SiO₂ + TiO₂, CaO + MgO, Fe₂O₃ + Na₂O + K₂O) by Ganapathy's Eq. (13).

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperBoiler

Inputs

Examples: Ganapathy: 20/30/15/20 %High-alumina Indian coal ash

Results

A quick estimate only; ASTM D1857 or ISO 540 fusion tests give the deformation, softening, hemispherical and flow temperatures.

The listed oxides add to only 85.0 % of the ash; check the analysis, since the estimate assumes they make up nearly all of it.

Estimated ash melting temperature (indicative, not a specific ASTM point)1,100.0°C

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Ganapathy: 20/30/15/20 %. The inputs, in the units selected above:

InputValue
Al₂O₃20.000 %
SiO₂ + TiO₂30.000 %
CaO + MgO15.000 %
Fe₂O₃ + Na₂O + K₂O20.000 %

Applying the formula below gives:

ResultValue
Estimated ash melting temperature (indicative, not a specific ASTM point)1,100.0 °C

Open this example in the calculator and change any input.

Formula

\(t_m = 19\,Al_2O_3 + 15\,(SiO_2 + TiO_2) + 10\,(CaO + MgO) + 6\,(Fe_2O_3 + Na_2O + K_2O) \ \ (°C,\ \%)\)

Variables

Symbol Meaning SI unit
\(Al_2O_3\) Al₂O₃ -
\(SiO_2 + TiO_2\) SiO₂ + TiO₂ -
\(CaO + MgO\) CaO + MgO -
\(Fe_2O_3 + Na_2O + K_2O\) Fe₂O₃ + Na₂O + K₂O -
\(t_m\) Estimated ash fusion temperature K

Method and standards

Ganapathy's Eq. (13).

Where it is used

  • Screening coals for slagging.
  • Comparing coal blends.

Common mistakes

  • Treating it as the ASTM initial deformation temperature.

Assumptions and limits

  • Oxides in % of ash; coal ashes. Results outside about 1000–1600 °C, as for a single pure oxide, are flagged as unreliable.
  • The source gives one "ash melting" temperature; it is not tied to the deformation, softening, hemispherical or flow temperature of ASTM D1857 or ISO 540, nor to a reducing or oxidising atmosphere. Use it to rank coals, not for design.
  • The listed oxides should make up nearly all the ash: a sum above 100 % is rejected and a sum below 90 % gives a warning.

References

  • Ganapathy
  • Steam Plant Calculations Manual
  • 2nd ed. (Marcel Dekker, 1993)
  • Q2.17
  • Eq. (13)

Questions and answers

Why does ash fusion matter?

Low-melting ash slags furnace walls and superheaters, raising furnace exit temperature.

Which oxides raise it?

Alumina and silica; fluxes such as iron, calcium and alkalis lower it.

What does Ganapathy's example give?

20 % Al₂O₃, 30 % SiO₂ + TiO₂, 15 % CaO + MgO, 20 % Fe₂O₃ + Na₂O + K₂O gives 1,100 °C.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.