Worked example
Example: Furnace oil 180 cSt at 50 °C, 30 cSt at 100 °C; at 120 °C; 15 cSt target. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Temperature of the first known point | 50.000 °C |
| Viscosity at the first point | 180.00 cSt |
| Temperature of the second known point | 100.00 °C |
| Viscosity at the second point | 30.000 cSt |
| Temperature wanted | 120.00 °C |
| Target viscosity (atomising or pumping) | 15.000 cSt |
Applying the formula below gives:
| Result | Value |
|---|---|
| Viscosity at the temperature wanted | 18.276 cSt |
| Oil temperature for the target viscosity | 129.13 °C |
| Viscosity-temperature slope (D341) | 2.8997 |
Open this example in the calculator and change any input.
Formula
\(\log\log(\nu + 0.7) = A - B\,\log T \quad (\nu\ \text{in cSt},\ T\ \text{in K})\)
\(B = \frac{Z_1 - Z_2}{\log T_2 - \log T_1},\quad Z_i = \log\log(\nu_i + 0.7) \qquad \nu_3 = 10^{10^{A - B\log T_3}} - 0.7 \qquad T_t = 10^{(A - Z_t)/B}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(T_1\), \(T_2\) | temperatures of the known points | K |
| \(\nu_1\), \(\nu_2\) | viscosities at the known points | m²/s (cSt in the equation) |
| \(T_3\) | temperature wanted | K |
| \(\nu_t\) | target viscosity | m²/s |
| \(\nu_3\) | viscosity at \(T_3\) | m²/s |
| \(T_t\) | temperature for the target viscosity | K |
| \(B\) | slope of the D341 line | – |
| \(A\) | intercept of the D341 line | – |
| \(Z\) | \(\log\log(\nu + 0.7)\) | – |
Method and standards
The Walther equation of ASTM D341 through two measured points. Logarithms are base 10.
Where it is used
- Setting oil heater outlet temperature for atomisation.
- Pumping and line heating of heavy oils.
- Comparing oils from different suppliers.
Common mistakes
- Extrapolating far below the pour point or above the flash point.
- Mixing kinematic (cSt) and dynamic (cP) viscosity.
- Using Redwood seconds without converting.
Assumptions and limits
- Simple D341 form, good above about 2 cSt; newer editions add terms for very thin oils.
- Outside the two known temperatures the result is extrapolated (a warning appears); check against the pour point and the flash point.
References
- ASTM D341 Viscosity–Temperature Charts for Liquid Petroleum Products (classic Walther form with the constant 0.7)
Questions and answers
How do I find fuel oil viscosity at another temperature?
From two known points on the ASTM D341 straight line. Oil at 180 cSt at 50 °C and 30 cSt at 100 °C has 18.3 cSt at 120 °C, and reaches 15 cSt at about 129 °C.
Why two points?
The D341 line has two constants; one viscosity and the oil grade are not enough. Supplier certificates usually give viscosity at 50 °C or 40 °C and 100 °C.
What viscosity does a burner need?
The burner maker states it; pressure-jet burners need thinner oil than rotary-cup or steam-atomised ones.
Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.