Worked example
Example: Indian coal 50 t/h, 35 % ash, 2 % carbon in residue, 80 % fly ash. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Fuel firing rate | 50,000 kg/h |
| Ash in the fuel, as fired | 35.000 % |
| Carbon in the residue (unburned carbon) | 2.0000 % |
| Share of the residue leaving as fly ash | 80.000 % |
| Operating hours per year | 8,000.0 h |
Applying the formula below gives:
| Result | Value |
|---|---|
| Total residue (ash plus unburned carbon) | 17.857 t/h |
| Fly ash | 14.286 t/h |
| Bottom ash | 3.5714 t/h |
| Residue per year | 142,857 t |
| Unburned carbon in the residue | 357.14 kg/h |
Open this example in the calculator and change any input.
Formula
\(\dot m_r = \frac{\dot m_f\,A}{1 - c_r} \qquad \dot m_{fa} = x_f\,\dot m_r \qquad \dot m_{ba} = (1 - x_f)\,\dot m_r \qquad \dot m_c = c_r\,\dot m_r \qquad m_r = \dot m_r\,t_{op}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\dot m_f\) | fuel firing rate | kg/s |
| \(A\) | ash in the fuel as fired | – |
| \(c_r\) | carbon in the residue | – |
| \(x_f\) | share of the residue leaving as fly ash | – |
| \(t_{op}\) | operating hours per year | s |
| \(\dot m_r\) | total residue | kg/s |
| \(\dot m_{fa}\) | fly ash | kg/s |
| \(\dot m_{ba}\) | bottom ash | kg/s |
| \(m_r\) | residue per year | kg |
| \(\dot m_c\) | unburned carbon in the residue | kg/s |
Method and standards
Mass balance on the incombustible matter: all the fuel ash leaves as residue together with the unburned carbon, as in the residue terms of ASME PTC 4-2013.
Where it is used
- Sizing ash handling systems, silos and ash ponds.
- Planning fly ash sale to cement plants.
- Comparing coals by the ash they leave.
Common mistakes
- Forgetting unburned carbon, which adds to the ash mass.
- Using the air-dried ash content with an as-fired coal flow.
- Assuming one fly-ash share for every boiler type.
Assumptions and limits
- Ash content as fired; limestone or sorbent added for desulphurisation adds to the residue (see the limestone calculator).
- One carbon content for all residue streams; fly ash and bottom ash usually differ.
- The fly-ash share splits the residue including its carbon, so with one carbon content it equals the split of the fuel ash.
- The ash content must be on the as-fired basis of the firing rate; an air-dried or dry-basis ash with an as-fired rate overstates the residue.
References
- Mass balance on fuel ash; ASME PTC 4-2013 (residue and unburned carbon)
Questions and answers
How much ash does a coal boiler produce?
Residue = fuel × ash ÷ (1 − carbon in residue). 50 t/h of 35 %-ash coal with 2 % carbon in the residue gives 17.9 t/h of ash, about 14.3 t/h as fly ash and 3.6 t/h as bottom ash with an 80/20 split.
Why does unburned carbon matter?
The residue is ash plus the carbon that did not burn, so a high carbon loss increases the ash to handle as well as costing efficiency.
Where does the fly-ash share come from?
From the firing system and the boiler maker; pulverised coal sends most ash to the fly ash, grates keep more as bottom ash.
Method and article reviewed by FireCAD engineering on 10 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.