Worked example
Example: 30 t/h coal, 30 % ash, 0.8 % S, Ca/S 2.2. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Fuel feed | 30.000 t/h |
| Ash in fuel, as fired | 30.000 % |
| Sulphur in fuel, as fired | 0.80000 % |
| Ca/S molar ratio | 2.2000 - |
| Sulphur capture | 90.000 % |
| CaCO₃ in limestone | 90.000 % |
| Bed drain design share of total solids | 60.000 % |
| Fly ash design share of total solids | 90.000 % |
| Capacity margin | 25.000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Limestone feed | 1.8315 t/h |
| CaSO₄ formed | 0.91718 t/h |
| Free CaO | 0.54573 t/h |
| Total solid residue | 10.646 t/h |
| Bed drain design capacity | 7.9845 t/h |
| Fly ash system design capacity | 11.977 t/h |
Open this example in the calculator and change any input.
Formula
\(\dot n_S = \frac{\dot m_fS}{32.06}, \quad \dot m_{ls} = \frac{(Ca/S)\dot n_S\,100.09}{x_{CaCO_3}}, \quad \dot m_{CaSO_4} = \eta_S\dot n_S\,136.14, \quad \dot m_{CaO} = (Ca/S - \eta_S)\dot n_S\,56.08\)
\(\dot m_{res} = \dot m_fA + \dot m_{CaSO_4} + \dot m_{CaO} + \dot m_{ls}(1 - x_{CaCO_3})\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\dot m_f\) | Fuel feed | kg/s |
| \(A\) | Ash in fuel | - |
| \(S\) | Sulphur in fuel | - |
| \(Ca/S\) | Ca/S molar ratio | - |
| \(\eta_S\) | Sulphur capture | - |
| \(x_{CaCO_3}\) | CaCO₃ in limestone | - |
| \(f_{bd}\) | Bed drain design share of total solids | - |
| \(f_{fa}\) | Fly ash design share of total solids (Basu: 90 %) | - |
| \(m\) | Capacity margin | - |
| \(\dot m_{ls}\) | Limestone feed | kg/s |
| \(\dot m_{CaSO_4}\) | CaSO₄ formed | kg/s |
| \(\dot m_{CaO}\) | Free CaO | kg/s |
| \(\dot m_{res}\) | Total solid residue | kg/s |
| \(\dot m_{bd}\) | Bed drain design capacity | kg/s |
| \(\dot m_{fa}\) | Fly ash system design capacity | kg/s |
| \(\dot m_{bd}\), \(\dot m_{fa}\) | \(= \dot m_{res}\,f\,(1 + m)\) with \(f = f_{bd}\) or \(f_{fa}\) | kg/s |
Method and standards
Stoichiometric residue balance with Basu's design shares; molar masses from IUPAC atomic weights (S 32.06, CaCO₃ 100.09, CaSO₄ 136.13, CaO 56.08 kg/kmol).
Where it is used
- CFB ash handling and silo sizing.
- Limestone and residue logistics.
Common mistakes
- Sizing ash systems on fuel ash only.
- Using the typical split without margin.
Assumptions and limits
- Complete calcination; CaSO₄ the only sulphur product.
- Unburnt carbon in the residue is not included, so the residue is somewhat understated for fuels with high carbon loss.
- Everything in the limestone that is not CaCO₃ is taken as a non-volatile inert. MgCO₃ in dolomitic limestone loses its CO₂, so the residue is then slightly overstated.
- Ash and sulphur are on the as-fired basis of the fuel feed.
References
- Basu
- Circulating Fluidized Bed Boilers: Design
- Operation and Maintenance (Springer, 2015)
- ch. 6
- Bed Drain Capacity and sec. 6.5.7 (ash split) and the CaCO₃–CaSO₄ stoichiometry
Questions and answers
Why is CFB residue larger than the fuel ash?
Spent limestone adds CaSO₄, free CaO and limestone inerts; at Ca/S 2–2.5 it can equal the fuel ash itself in high-sulphur fuels.
How is ash split between bed and fly ash?
It depends on fuel ash particle size and attrition; most passes the cyclone as fly ash, so both systems are designed with wide margins.
What do the defaults give?
30 t/h of 30 % ash, 0.8 % S coal at Ca/S 2.2: about 1.8 t/h of limestone and 10.6 t/h of total residue.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.