FireCADCalc

AFBC Bed Area from Superficial Velocity

Bed plan area of an atmospheric fluidised-bed (AFBC) boiler from the fluidising air flow, bed temperature and the chosen superficial velocity.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationPulp and paperFood, dairy and textileBoiler

Inputs

Examples: Air 20 kg/s, bed 850 °C, 2.0 m/sAir 8 kg/s, 880 °C, 2.5 m/sAir 40 kg/s, 850 °C, 1.8 m/s, 600 m site

The boiler maker's design value for the bed material and fuel.

Results

Air volume is used; the gas in the bed also carries combustion products and fuel moisture, which add a few per cent for dry coal and 10 % or more for wet biomass, so the bed needs that much more area.

Bed plan area31.818m²
Gas volume flow at bed temperature229,086m³/h
Side of an equivalent square bed5.6407m

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Air 20 kg/s, bed 850 °C, 2.0 m/s. The inputs, in the units selected above:

InputValue
Fluidising air flow72,000 kg/h
Bed temperature850.00 °C
Pressure above the bed (absolute)1.0132 bar
Superficial velocity at bed temperature2.0000 m/s

Applying the formula below gives:

ResultValue
Bed plan area31.818 m²
Gas volume flow at bed temperature229,086 m³/h
Side of an equivalent square bed5.6407 m

Open this example in the calculator and change any input.

Formula

\(\dot V = \frac{\dot m_a}{\rho(T_b, p)} \qquad A_b = \frac{\dot V}{u_0} \qquad s = \sqrt{A_b}\)

Variables

Symbol Meaning SI unit
\(\dot m_a\) fluidising air flow kg/s
\(T_b\) bed temperature K
\(p\) pressure above the bed Pa
\(u_0\) superficial velocity m/s
\(A_b\) bed plan area m²
\(\dot V\) gas volume at bed temperature m³/s
\(s\) side of an equivalent square m
\(\rho\) air density at bed conditions kg/m³

Method and standards

Air density at bed temperature by the ideal-gas law (dry air molar mass); volume flow over superficial velocity.

Where it is used

  • First sizing of AFBC boilers.
  • Checking an existing bed for a higher load.
  • Explaining elutriation and erosion problems.

Common mistakes

  • Using ambient air density.
  • Ignoring the gas added by combustion and moisture.
  • Choosing velocity without checking U_mf of the coarsest particles.

Assumptions and limits

  • Air as the gas; uniform distribution across the bed. Combustion products and fuel moisture raise the gas volume a few per cent for dry coal and 10 % or more for wet biomass; allow for it in the area.
  • The velocity is not checked against the bed material's minimum fluidisation or terminal velocity; a warning appears outside the usual 1–3 m/s of bubbling beds.

References

  • Continuity with the ideal-gas law for air

Questions and answers

How big a bed does an AFBC boiler need?

Gas volume at bed temperature divided by the superficial velocity. 20 kg/s of air at 850 °C is 63.6 m³/s; at 2.0 m/s the bed needs 31.8 m², a square of 5.6 m.

Why use the bed temperature?

The air expands about four times from ambient to 850 °C, so the velocity in the bed is set by the hot volume.

What velocity should I choose?

The boiler maker's design value: high enough to fluidise the coarse bed particles, low enough to limit elutriation of fines and erosion of in-bed tubes.

Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.