Worked example
Example: 250 TCH. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Crushing rate | 250.00 t/h |
| Fibre % cane | 14.500 % |
| Pressure feeder roller diameter | 0.80000 m |
| Roller length | 2.0000 m |
| Opening between the feeder rollers | 120.00 mm |
| Mill roller speed (0 if not checked) | 0 rpm |
Applying the formula below gives:
| Result | Value |
|---|---|
| Swept volume needed (3.8 A f m³/h) | 137.75 m³/h |
| Fibre index of the feed (fixed by Crawford's rule, 1/3.8 t/m³) | 263.16 kg/m³ |
| Feeder roller speed for that volume | 3.8062 rpm |
| Feeder roller peripheral speed | 9.5660 m/min |
Open this example in the calculator and change any input.
Formula
\(\dot V = 3.8\,A f \;[\mathrm{m^3/h}], \quad v_p = \frac{\dot V}{L\,e_p}, \quad n_p = \frac{v_p}{\pi D_p}, \quad \varphi = \frac{A f}{\dot V} = \frac{1}{3.8}\ \mathrm{t/m^3}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(A\) | Crushing rate | kg/s |
| \(f\) | Fibre % cane | - |
| \(D_p\) | Pressure feeder roller diameter | m |
| \(L\) | Roller length | m |
| \(e_p\) | Opening between the feeder rollers | m |
| \(n_m\) | Mill roller speed (0 if not checked) | 1/s |
| \(\dot V\) | Swept volume needed (3.8 A f m³/h) | m³/s |
| \(\varphi\) | Fibre index of the feed (fixed by Crawford's rule, 1/3.8 t/m³) | kg/m³ |
| \(n_p\) | Feeder roller speed for that volume | 1/s |
| \(v_p\) | Feeder roller peripheral speed | m/s |
Method and standards
Crawford's swept-volume rule as given by Hugot, with continuity through the feeder opening.
Where it is used
- Sizing pressure feeders.
- Checking feeder speed after a crush increase.
Common mistakes
- Using cane rate for fibre rate.
- Taking the opening at the empty setting.
Assumptions and limits
- Steady feed; opening under load.
- In 3.8 A f, A is in t/h and f is a fraction (A f is fibre in t/h), giving m³/h. The fibre index is then fixed at 1/3.8 t/m³ (about 263 kg/m³) whatever the inputs.
- The mill speed is optional; when given, the feeder speed is compared with Hugot's 1.3–1.7 times.
References
- Hugot
- Handbook of Cane Sugar Engineering
- 3rd ed. (Elsevier, 1986)
- ch. 8
- pressure feeders and Crawford's eqn 8.14
- pp. 94–97
Questions and answers
What does 3.8 A f mean?
Crawford's rule: about 3.8 m³ of swept volume per hour for each tonne of fibre per hour, a fibre index near 265 kg/m³.
How fast do the rollers run?
About one and a half times the mill speed.
Why a pressure feeder?
It forces bagasse into the mill, raising capacity and allowing heavier imbibition without choking.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.