FireCADCalc

Pressure Feeder Swept Volume and Speed

Volume a pressure feeder must sweep for the fibre it feeds (Crawford, after Hugot eqn 8.14), and the roller speed that gives it for a diameter, length and opening.

Sugar mill and cogeneration

Inputs

Examples: 250 TCH150 TCH, mill at 5 rpm

Optional: the speed of the mill the feeder serves, to compare with Hugot's 1.3–1.7 times.

Results

Hugot: pressure feeder rollers run about 1.5 times the mill speed (1.3–1.7).

Feeder speed is 0.81 times the mill speed, outside Hugot's 1.3–1.7.

Swept volume needed (3.8 A f m³/h)91.200m³/h
Fibre index of the feed (fixed by Crawford's rule, 1/3.8 t/m³)263.16kg/m³
Feeder roller speed for that volume4.0658rpm
Feeder roller peripheral speed8.9412m/min

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 250 TCH. The inputs, in the units selected above:

InputValue
Crushing rate250.00 t/h
Fibre % cane14.500 %
Pressure feeder roller diameter0.80000 m
Roller length2.0000 m
Opening between the feeder rollers120.00 mm
Mill roller speed (0 if not checked)0 rpm

Applying the formula below gives:

ResultValue
Swept volume needed (3.8 A f m³/h)137.75 m³/h
Fibre index of the feed (fixed by Crawford's rule, 1/3.8 t/m³)263.16 kg/m³
Feeder roller speed for that volume3.8062 rpm
Feeder roller peripheral speed9.5660 m/min

Open this example in the calculator and change any input.

Formula

\(\dot V = 3.8\,A f \;[\mathrm{m^3/h}], \quad v_p = \frac{\dot V}{L\,e_p}, \quad n_p = \frac{v_p}{\pi D_p}, \quad \varphi = \frac{A f}{\dot V} = \frac{1}{3.8}\ \mathrm{t/m^3}\)

Variables

Symbol Meaning SI unit
\(A\) Crushing rate kg/s
\(f\) Fibre % cane -
\(D_p\) Pressure feeder roller diameter m
\(L\) Roller length m
\(e_p\) Opening between the feeder rollers m
\(n_m\) Mill roller speed (0 if not checked) 1/s
\(\dot V\) Swept volume needed (3.8 A f m³/h) m³/s
\(\varphi\) Fibre index of the feed (fixed by Crawford's rule, 1/3.8 t/m³) kg/m³
\(n_p\) Feeder roller speed for that volume 1/s
\(v_p\) Feeder roller peripheral speed m/s

Method and standards

Crawford's swept-volume rule as given by Hugot, with continuity through the feeder opening.

Where it is used

  • Sizing pressure feeders.
  • Checking feeder speed after a crush increase.

Common mistakes

  • Using cane rate for fibre rate.
  • Taking the opening at the empty setting.

Assumptions and limits

  • Steady feed; opening under load.
  • In 3.8 A f, A is in t/h and f is a fraction (A f is fibre in t/h), giving m³/h. The fibre index is then fixed at 1/3.8 t/m³ (about 263 kg/m³) whatever the inputs.
  • The mill speed is optional; when given, the feeder speed is compared with Hugot's 1.3–1.7 times.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 8
  • pressure feeders and Crawford's eqn 8.14
  • pp. 94–97

Questions and answers

What does 3.8 A f mean?

Crawford's rule: about 3.8 m³ of swept volume per hour for each tonne of fibre per hour, a fibre index near 265 kg/m³.

How fast do the rollers run?

About one and a half times the mill speed.

Why a pressure feeder?

It forces bagasse into the mill, raising capacity and allowing heavier imbibition without choking.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.