FireCADCalc

Steam Flow Meter Pressure and Temperature Correction

Corrects the reading of an orifice (DP) or vortex steam flow meter that runs away from its design pressure and temperature, using IAPWS-IF97 steam densities.

Thermal power plantProcess steam and utilitiesRefinery and petrochemicalChemical and fertiliserIAPWS-IF97 (water and steam)ISO 5167 (differential-pressure flow)Boiler

Inputs

Examples: Orifice set for 10.5 bar(a) sat, running at 8 bar(a) sat, reads 10 t/hVortex set for 45 bar(a)/400 °C, running at 40 bar(a)/380 °C, reads 30 t/hOrifice set for 17.5 bar(a) sat, running at 18.5 bar(a)/230 °C, reads 5 t/h

Design (calibration) conditions

Actual conditions

Results

Assumes the meter shows mass flow computed with the design density; a meter with live pressure and temperature compensation needs no correction.

Corrected (true) steam flow4,967.1kg/h
Correction factor0.99341
Steam density at design8.8161kg/m³
Steam density actual8.7004kg/m³

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Orifice set for 10.5 bar(a) sat, running at 8 bar(a) sat, reads 10 t/h. The inputs, in the units selected above:

InputValue
Meter reading (mass flow)10,000 kg/h
Meter typeDifferential pressure (orifice, nozzle, venturi)
Design pressure (absolute)10.500 bar
Design steam conditionDry saturated
Design temperature (superheated only)250.00 °C
Actual pressure (absolute)8.0000 bar
Actual steam conditionDry saturated
Actual temperature (superheated only)250.00 °C

Applying the formula below gives:

ResultValue
Corrected (true) steam flow8,785.7 kg/h
Correction factor0.87857
Steam density at design5.3907 kg/m³
Steam density actual4.1610 kg/m³

Open this example in the calculator and change any input.

Formula

\(k_{DP} = \sqrt{\frac{\rho_a}{\rho_d}} \qquad k_{vol} = \frac{\rho_a}{\rho_d} \qquad \dot m = k\,\dot m_i\)

Variables

Symbol Meter or quantity SI unit
\(\dot m_i\) meter reading kg/s
\(\text{meter}\) differential pressure or volumetric –
\(p_d\) design pressure, absolute Pa
\(\text{state}_d\) design steam condition –
\(T_d\) design temperature K
\(p_a\) actual pressure, absolute Pa
\(\text{state}_a\) actual steam condition –
\(T_a\) actual temperature K
\(\dot m\) corrected steam flow kg/s
\(k\) correction factor –
\(\rho_d\) steam density at design kg/m³
\(\rho_a\) steam density actual kg/m³

Method and standards

Differential-pressure meters follow √(Δp·ρ) (the principle of ISO 5167); volumetric meters measure volume, so mass scales with density. Steam densities from FireCAD's IAPWS-IF97.

Where it is used

  • Correcting steam totals for efficiency and cost reports.
  • Checking whether a meter needs compensation.
  • Reconciling boiler and user steam meters.

Common mistakes

  • Using gauge pressure.
  • Assuming saturated steam when it is superheated.
  • Correcting a meter that already has live compensation.

Assumptions and limits

  • Dry steam; the meter's other coefficients unchanged.
  • Wet steam cannot be entered. A DP meter in wet steam reads high (the liquid adds to the differential), so applying only this density correction under-corrects; wet steam needs a two-phase meter correction and a known dryness fraction.

References

  • IAPWS R7-97(2012) IF97
  • ISO 5167 (DP meters: mass flow proportional to the square root of density)

Questions and answers

How wrong is an uncompensated steam meter?

An orifice meter set up for 10.5 bar(a) saturated steam but running at 8 bar(a) reads 10 t/h when only 8.79 t/h flows, 14 % high. A vortex meter showing mass with fixed density errs twice as much, because it measures volume.

Why the square root for orifice meters?

The differential pressure is ρv²/2, so mass flow is proportional to √(Δp·ρ); with ρ fixed in the transmitter, the reading scales with √(ρ_actual/ρ_design).

How do I avoid this?

Fit pressure (and for superheated steam, temperature) compensation in the flow computer, or correct the totals with this factor.

Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.