FireCADCalc

RC and RL Time Constant, Charging and Cut-off Frequency

Time constant of an RC or RL circuit, the share of the final value and the voltage or current reached after a given time, the cut-off frequency and stored energy.

Electrician and wireman licence examinations

Inputs

Examples: RC 10 kΩ, 100 µF, 12 V, after 1 sRL 100 Ω, 0.5 H, 24 V, after 2 msRC 1 MΩ, 1 µF, 5 V, after 3 s

Results

Time constant1.0000s
Time to about 99.3 % (five time constants)5.0000s
Share of the final value reached at t63.212%
Capacitor voltage at t (RC, charging)7.5854V
Current at t4.4146e-04A
Cut-off frequency 1/(2πτ)0.15915Hz
Energy stored when fully charged0.007200J

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: RC 10 kΩ, 100 µF, 12 V, after 1 s. The inputs, in the units selected above:

InputValue
CircuitRC (resistor and capacitor)
Resistance10.000 kΩ
Capacitance (RC)100.00 µF
Inductance (RL)500.00 mH
Step (supply) voltage12.000 V
Time after the step1.0000 s

Applying the formula below gives:

ResultValue
Time constant1.0000 s
Time to about 99.3 % (five time constants)5.0000 s
Share of the final value reached at t63.212 %
Capacitor voltage at t (RC, charging)7.5854 V
Current at t4.4146e-04 A
Cut-off frequency 1/(2πτ)0.15915 Hz
Energy stored when fully charged0.007200 J

Open this example in the calculator and change any input.

Formula

\(\tau = R C \quad \text{or} \quad \tau = L / R\)

\(1 - e^{-t/\tau}, \quad v_C = V \left(1 - e^{-t/\tau}\right)\)

\(i(t) = \frac{V}{R} e^{-t/\tau}\ (\text{RC}), \quad i(t) = \frac{V}{R}\left(1 - e^{-t/\tau}\right)\ (\text{RL})\)

\(f_c = \frac{1}{2\pi\tau}, \quad W = \tfrac12 C V^2\ \text{or}\ \tfrac12 L I^2\)

Variables

Symbol Meaning SI unit
\(\text{circuit}\) Circuit -
\(R\) Resistance Ω
\(C\) Capacitance (RC) F
\(L\) Inductance (RL) H
\(V\) Step (supply) voltage V
\(t\) Time after the step s
\(\tau\) Time constant s
\(5\tau\) Time to about 99.3 % (five time constants) s
\(1 - e^{-t/\tau}\) Share of the final value reached at t -
\(v_C\) Capacitor voltage at t (RC, charging) V
\(i(t)\) Current at t A
\(f_c\) Cut-off frequency 1/(2πτ) 1/s
\(W\) Energy stored when fully charged J
\(I\) Final current V/R (RL) A

Method and standards

A first-order circuit driven by a voltage step approaches its final value exponentially with time constant τ. The cut-off frequency of the same circuit used as a filter is 1/(2πτ).

Where it is used

  • Timing circuits, signal filters and snubbers.
  • Discharge time of capacitors for safety.
  • Contactor coil and relay pick-up times.

Common mistakes

  • Using diameter-style units (µF entered as F).
  • Forgetting the source resistance in series.
  • Assuming the capacitor is empty at the start.

Assumptions and limits

  • Ideal components; step input; starts from zero.

References

  • First-order circuit response (exponential charging)

Questions and answers

How long does a 10 kΩ, 100 µF circuit take to charge?

τ = RC = 1 s. After 1 s it reaches 63.2 % (7.6 V of 12 V) and after 5 s about 99.3 %.

What is the cut-off frequency?

1/(2πτ): 0.16 Hz for τ = 1 s. Above it an RC low-pass filter attenuates by 20 dB per decade.

How does an RL circuit differ?

τ = L/R and it is the current that rises: a 0.5 H, 100 Ω coil on 24 V reaches 33 % of its 0.24 A after 2 ms.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.