FireCADCalc

Voltage Divider Calculator (with Load)

Output voltage of a two-resistor voltage divider with and without a load, the current drawn, the power in the resistors and the Thévenin resistance.

Inputs

Examples: 24 V, 10 kΩ and 5 kΩ, 100 kΩ load5 V, 1 kΩ and 2 kΩ, 10 kΩ load230 V, 100 kΩ and 1 kΩ, 10 MΩ meter

Enter a very large value for no load.

Results

Output voltage, no load8.0000V
Output voltage with the load7.7419V
Current from the source (with the load)1.6258mA
Power taken from the source0.039019W
Thévenin (output) resistance R₁ ∥ R₂3,333.3Ω

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 24 V, 10 kΩ and 5 kΩ, 100 kΩ load. The inputs, in the units selected above:

InputValue
Input voltage24.000 V
Upper resistor10,000 Ω
Lower resistor (output across it)5,000.0 Ω
Load resistance across the output100,000 Ω

Applying the formula below gives:

ResultValue
Output voltage, no load8.0000 V
Output voltage with the load7.7419 V
Current from the source (with the load)1.6258 mA
Power taken from the source0.039019 W
Thévenin (output) resistance R₁ ∥ R₂3,333.3 Ω

Open this example in the calculator and change any input.

Formula

\(V_o = V_{in}\, \frac{R_2}{R_1 + R_2}, \quad V_L = V_{in}\, \frac{R_2 \parallel R_L}{R_1 + R_2 \parallel R_L}\)

Variables

Symbol Meaning SI unit
\(V_{in}\) Input voltage V
\(R_1\) Upper resistor Ω
\(R_2\) Lower resistor (output across it) Ω
\(R_L\) Load resistance across the output Ω
\(V_{o}\) Output voltage, no load V
\(V_{L}\) Output voltage with the load V
\(I\) Current from the source (with the load) A
\(P\) Power taken from the source W
\(R_{th}\) Thévenin (output) resistance R₁ ∥ R₂ Ω

Method and standards

Series circuit with the load in parallel with R₂.

Where it is used

  • Sensor and ADC input scaling.
  • Bias networks.

Common mistakes

  • Ignoring the load.
  • Resistor power rating.

Assumptions and limits

  • Ideal source.

References

  • Kirchhoff's laws; Thévenin's theorem

Questions and answers

What does 24 V across 10 kΩ and 5 kΩ give?

8 V unloaded; with a 100 kΩ load 7.74 V.

Why does the load lower the voltage?

It parallels R₂; keep the load at least ten times R₂.

What is the output resistance?

R₁ in parallel with R₂.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.