FireCADCalc

Rice Husk as Boiler Fuel: Steam and Power Potential

Husk from paddy milled, its heat, the steam it raises at a boiler efficiency and enthalpy rise, the power at a turbine steam rate, and the ash.

Process steam and utilitiesFood, dairy and textileBoiler

Inputs

Examples: 300 t/d paddy, 14 MJ/kg huskLarge mill 600 t/d

Gross calorific value of the husk as fired (as received), on the same moisture basis as the husk share and the ash.

Results

Husk ash is mostly silica; keep bed and furnace temperatures below its fusion range and handle the ash dust-free.

The power potential sends all the steam through the turbine: deduct process steam for parboiling and drying first.

Husk60.000t/d
Heat input9.7222MW
Steam9.0741t/h
Power potential1,814.8kW
Ash10.800t/d

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 300 t/d paddy, 14 MJ/kg husk. The inputs, in the units selected above:

InputValue
Paddy milled300.00 t/d
Husk share of paddy20.000 %
Husk calorific value (as fired)14.000 MJ/kg
Boiler efficiency (GCV)70.000 %
Enthalpy rise feedwater to steam2,700.0 kJ/kg
Turbine steam rate5.0000 kg/kWh
Ash in husk (as fired)18.000 %

Applying the formula below gives:

ResultValue
Husk60.000 t/d
Heat input9.7222 MW
Steam9.0741 t/h
Power potential1,814.8 kW
Ash10.800 t/d

Open this example in the calculator and change any input.

Formula

\(\dot M_h = h\dot M, \quad Q = \dot M_h GCV, \quad \dot M_a = a\dot M_h, \quad \dot m_s = \frac{\eta\dot M_hGCV}{\Delta h}, \quad P = \frac{\dot m_s}{SSC}\)

Variables

Symbol Meaning SI unit
\(\dot M\) Paddy milled kg/s
\(h\) Husk share of paddy -
\(GCV\) Husk calorific value (as fired) J/kg
\(\eta\) Boiler efficiency (GCV) -
\(\Delta h\) Enthalpy rise feedwater to steam J/kg
\(SSC\) Turbine steam rate kg/J
\(a\) Ash in husk (as fired) -
\(\dot M_h\) Husk kg/s
\(Q\) Heat input W
\(\dot m_s\) Steam kg/s
\(P\) Power potential W
\(\dot M_a\) Ash kg/s

Method and standards

Fuel energy chain.

Where it is used

  • Rice mill cogeneration studies.

Common mistakes

  • Using as-received CV with dry husk mass.
  • Ignoring ash handling.

Assumptions and limits

  • Steady supply.
  • Calorific value, husk share and ash on one moisture basis (as fired).
  • The power potential assumes all the steam goes through the turbine; process steam (parboiling, drying) is not deducted.

References

  • Definitions and mass and energy balances

Questions and answers

How much husk per tonne of paddy?

About 200 kg.

What heating value?

About 13–15 MJ/kg gross.

Is there surplus husk?

Usually yes for raw rice mills; parboiling and drying use much of it.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.