FireCADCalc

Paddy Parboiling: Soak Water and Steaming

Hot water for soaking and steam for heating and steaming paddy in parboiling, from batch size, water ratio, temperatures and steam per kg for steaming (IF97 steam).

Food, dairy and textileIAPWS-IF97 (water and steam)Boiler

Inputs

Examples: 10 t paddy, hot soak 70 °CPressure parboiling

Results

Hot soaking at 65–70 °C cuts soak time from days to 3–4 hours; drain water carries heat that can be recovered.

Soak heating steam is credited with its latent heat only (indirect heating, condensate leaving saturated). Steam sparged into the soak also gives up the condensate's heat down to the soak temperature, so less steam is needed (about 13 % less at 4 bar and 70 °C).

Soak water12,000kg
Heat to the soak water and paddy3.0709GJ
Steam to heat the soak1,439.5kg
Steam for steaming1,200.0kg
Total steam2,639.5kg

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 10 t paddy, hot soak 70 °C. The inputs, in the units selected above:

InputValue
Paddy batch10,000 kg
Soak water to paddy ratio1.2000 kg/kg
Fresh water temperature25.000 °C
Soaking temperature70.000 °C
Paddy specific heat1.8000 kJ/(kg·K)
Steaming steam per kg paddy0.12000 kg/kg
Steam pressure (absolute)4.0000 bar

Applying the formula below gives:

ResultValue
Soak water12,000 kg
Heat to the soak water and paddy3.0709 GJ
Steam to heat the soak1,439.5 kg
Steam for steaming1,200.0 kg
Total steam2,639.5 kg

Open this example in the calculator and change any input.

Formula

\(M_w = r_wM, \quad Q_s = (M_wc_w + Mc_p)(T_s - T_1), \quad m_s = \frac{Q_s}{h_{fg}} + m_{st}M\)

Variables

Symbol Meaning SI unit
\(M\) Paddy batch kg
\(r_w\) Soak water to paddy ratio kg/kg
\(T_1\) Fresh water temperature K
\(T_s\) Soaking temperature K
\(c_p\) Paddy specific heat J/(kg·K)
\(m_{st}\) Steaming steam per kg paddy kg/kg
\(p_s\) Steam pressure (absolute) Pa
\(M_w\) Soak water kg
\(Q_s\) Heat to the soak water and paddy J
\(m_1\) Steam to heat the soak kg
\(m_2\) Steam for steaming kg
\(m_s\) Total steam kg
\(c_w\) Water specific heat, 4 186.8 J/(kg·K)
\(h_{fg}\) Latent heat of the steam at p_s (IF97) J/kg

Method and standards

Sensible heat with IF97 latent heat.

Where it is used

  • Parboiling plant design.

Common mistakes

  • Ignoring steam for steaming.
  • Counting drain water as recovered.

Assumptions and limits

  • No soak losses.
  • The soak is heated indirectly: steam gives its latent heat h_fg and leaves as saturated condensate. If steam is sparged directly into the soak, the condensate also cools to the soak temperature and the steam needed is lower (about 13 % less at 4 bar and 70 °C).
  • Water specific heat c_w = 4 186.8 J/(kg·K).

References

  • Definitions and mass and energy balances
  • Steam latent heat from IAPWS-IF97

Questions and answers

Why parboil?

Gelatinising the starch hardens the kernel, raising head rice yield and nutrition.

How much steam?

Typically 0.1–0.2 t of steam per tonne of paddy plus soak heating.

What does the husk supply?

Husk-fired boilers usually cover all parboiling and drying heat.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.