FireCADCalc

Toxic Dose and Probit: Probability of an Effect

Toxic load from concentration and exposure time (Cⁿt), the probit Y = a + b ln(Cⁿt) and the probability of the effect, from user probit constants.

Refinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 50 ppm for 30 min, illustrative constants500 ppm for 10 min, n = 1

The constants must be for C in ppm and t in minutes. Sets fitted to mg/m³ or to seconds have different a values: convert or use a matching set.

Results

Probit constants are substance- and effect-specific: take them from a recognised source (CCPS, TNO Green Book). The defaults are illustrative only. Screening estimate only, not a safety study or a basis for protective design.

Haber dose C·t (ppm·min)5,000.0
Toxic load (ppmⁿ·min)5,000.0
Probit7.0344
Probability of the effect97.904%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 50 ppm for 30 min, illustrative constants. The inputs, in the units selected above:

InputValue
Concentration50.000 ppm
Exposure time30.000 min
Probit constant a (for concentration in ppm and time in minutes)-8.2900 -
Probit constant b (ppm, minutes)0.92000 -
Concentration exponent n (ppm, minutes)2.0000 -

Applying the formula below gives:

ResultValue
Haber dose C·t (ppm·min)1,500.0
Toxic load (ppmⁿ·min)75,000
Probit2.0372
Probability of the effect0.15244 %

Open this example in the calculator and change any input.

Formula

\(D = C\,t, \quad Y = a + b\ln(C^nt), \quad P = \tfrac12\left[1 + \mathrm{erf}\left(\frac{Y - 5}{\sqrt2}\right)\right]\ \ (C\ \mathrm{ppm},\ t\ \mathrm{min})\)

Variables

Symbol Meaning SI unit
\(C\) Concentration -
\(t\) Exposure time s
\(a\) Probit constant a (for concentration in ppm and time in minutes) -
\(b\) Probit constant b (ppm, minutes) -
\(n\) Concentration exponent n (ppm, minutes) -
\(D\) Haber dose C·t (ppm·min) -
\(C^nt\) Toxic load (ppmⁿ·min) -
\(Y\) Probit -
\(P\) Probability of the effect -

Method and standards

Haber's law and the probit method.

Where it is used

  • Consequence screening for toxic releases.

Common mistakes

  • Mixing ppm and mg/m³ constants.
  • Using constants for another effect.

Assumptions and limits

  • Constant concentration during the exposure.
  • The probit constants must be for concentration in ppm and time in minutes; sets for mg/m³ or seconds need converting.

References

  • Perry's Chemical Engineers' Handbook
  • 9th ed. (McGraw-Hill, 2019)
  • sec. 23
  • Eq. (23-15) (Haber dose) and probit methods
  • Probit to probability: P = ½[1 + erf((Y − 5)/√2)]

Questions and answers

What is a probit?

A transformed probability: Y = 5 means 50 %, each unit is one standard deviation.

Why Cⁿt instead of C·t?

For many gases short high concentrations harm more than Haber's simple product implies; n > 1 captures that.

Where do a, b and n come from?

Published probit tables for each substance and effect; the defaults are illustrative.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.