FireCADCalc

Coal Drying in the Mill: Primary Air Temperature Needed

Water evaporated and heat needed to dry coal in a pulveriser, and the primary air temperature at the mill inlet that gives the chosen mill outlet temperature.

Thermal power plantProcess steam and utilitiesChemical and fertiliserPulp and paperASME PTC 4 (fired steam generators)IAPWS-IF97 (water and steam)BoilerBurner and furnace

Inputs

Examples: Bituminous 30 t/h, 15 % to 2 %, outlet 70 °C, air/coal 2.0Indian coal 40 t/h, 12 % to 1.5 %, outlet 75 °C, 1.8Lignite 25 t/h, 35 % to 10 %, outlet 65 °C, 3.0

From the coal analysis or the mill maker.
About 0.01 for temperate air, up to 0.02 to 0.03 for humid tropical air; from the psychrometric chart at the air intake.

Results

The mill outlet temperature limit depends on the coal's volatile matter (fire and explosion risk); check the mill maker's limit.

Water evaporated in the mill4.2640t/h
Heat taken by drying and heating the coal3,447.9kW
Primary air flow, dry72.000t/h
Primary air temperature needed at the mill inlet230.77°C

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Bituminous 30 t/h, 15 % to 2 %, outlet 70 °C, air/coal 2.0. The inputs, in the units selected above:

InputValue
Raw coal feed to the mill30.000 t/h
Total moisture of the raw coal15.000 %
Moisture left in the pulverised coal2.0000 %
Raw coal temperature30.000 °C
Specific heat of the dry coal1.2500 kJ/(kg·K)
Mill outlet temperature wanted70.000 °C
Primary air (dry) to coal ratio2.0000 kg/kg
Primary air humidity, kg water per kg dry air0.013000 kg/kg
Mill grinding power (enters as heat)150.00 kW
Heat lost from the mill casing and ducts50.000 kW

Applying the formula below gives:

ResultValue
Water evaporated in the mill3.9796 t/h
Heat taken by drying and heating the coal3,147.6 kW
Primary air flow, dry60.000 t/h
Primary air temperature needed at the mill inlet245.24 °C

Open this example in the calculator and change any input.

Formula

\(w = \frac{M_{in} - M_{out}}{1 - M_{out}}, \quad \dot m_w = \dot m_c w\)

\(Q_c = \dot m_w [h_v(T_o) - h_f(T_c)] + \dot m_c (1 - M_{in}) c_c (T_o - T_c) + \dot m_c (M_{in} - w) [h_f(T_o) - h_f(T_c)]\)

\(h_a(T) = h_{da}(T) + x_a h_{v,ig}(T)\)

\(\dot m_a = r\,\dot m_c, \quad \dot m_a [h_a(T_{in}) - h_a(T_o)] + P_m - Q_l = Q_c\)

Variables

Symbol Meaning SI unit
\(\dot m_c\) raw coal feed kg/s
\(M_{in}\) total moisture of the raw coal -
\(M_{out}\) moisture left in the pulverised coal -
\(T_c\) raw coal temperature K
\(c_c\) specific heat of the dry coal, ash included, as a constant mean value J/(kg·K)
\(P_m\) mill grinding power, entering as heat W
\(Q_l\) mill casing and duct heat loss W
\(\dot m_w\) water evaporated kg/s
\(Q_c\) heat taken by the coal side W
\(\dot m_a\) primary air flow, dry air kg/s
\(T_{in}\) primary air temperature at the mill inlet K
\(r\) primary air (dry) to coal ratio kg/kg
\(h_v\) water vapour enthalpy at T_o and 1 psia J/kg
\(h_f\) liquid water enthalpy J/kg
\(h_a\) humid air enthalpy per kg dry air: dry air plus x_a kg of ideal-gas water vapour J/kg
\(x_a\) primary air humidity, kg water vapour per kg dry air kg/kg
\(h_{da}\) dry air enthalpy J/kg
\(h_{v,ig}\) ideal-gas water vapour enthalpy J/kg
\(w\) water evaporated per kg raw coal kg/kg
\(T_o\) mill outlet temperature wanted K

Method and standards

A heat balance on the mill: the hot primary air gives up heat between the mill inlet and outlet temperatures; with the grinding power (which ends as heat) it evaporates the surface moisture and warms the coal and the water left in it. The evaporated water leaves as vapour (IAPWS-IF97 at 1 psia, as ASME PTC 4 treats flue gas moisture); the primary air is humid: per kg of dry air it carries x_a kg of water vapour, and its enthalpy is dry air plus that vapour as an ideal gas from NIST Shomate data, the basis ASME PTC 4 uses for moisture in air.

Where it is used

  • Checking whether the air heater can dry a wetter coal.
  • Setting the hot and tempering air mix for a target outlet temperature.
  • Explaining mill output limits in the monsoon.

Common mistakes

  • Using total moisture as the moisture removed: some stays in the pulverised coal.
  • Ignoring mill casing heat losses on long PA ducts.
  • Running outlet temperatures above the safe limit for high-volatile coal.

Assumptions and limits

  • Steady state; tempering air is assumed already mixed into the primary air.
  • The primary air flow and the air to coal ratio are on dry air; the humidity entered is carried as vapour and adds to the heat the air brings (about 2 % at 0.013 kg/kg).
  • No allowance for seal air or leakage.
  • The evaporated water is valued as vapour at 1 psia (the ASME PTC 4 flue-gas convention), not at the actual partial pressure in the mill; the difference is small.
  • A warning appears when the inlet air would need to be above 400 °C.

References

  • Mill heat balance
  • IAPWS-IF97
  • ASME PTC 4 (vapour at 1 psia)

Questions and answers

What primary air temperature dries coal with 15 % moisture?

In the example, 30 t/h dried to 2 % with an air to coal ratio of 2.0 and a 70 °C outlet needs air at about 245 °C at the mill inlet (primary air humidity 0.013 kg/kg).

Why does wet coal limit mill output?

The air heater can only supply so much hot air; when the drying heat needed exceeds it, the outlet temperature falls and the coal is fed slower.

Does grinding power help drying?

Yes: nearly all mill motor power ends as heat in the coal and air, reducing the air temperature needed.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.