FireCADCalc

Char Particle Burning Rate (Diffusion Limit) in a Fluidised Bed

Sherwood number (Halder–Basu), mass transfer coefficient and the diffusion-limited burning rate of a char particle in a fluidised bed (Basu Eqs. 4.7–4.10).

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperBoiler

Inputs

Examples: 6 mm char, 5 kPa O2, 900 °C10 mm char, CO at surface

Results

Particle Reynolds number100.00
Schmidt number0.71429
Sherwood number8.6221
Mass transfer coefficient, kg C/(m²·s·kPa O₂)4.2732e-04
Diffusion-limited burning rate12.307kg/(m²·h)
Carbon burnt per particle3.8663g/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 6 mm char, 5 kPa O2, 900 °C. The inputs, in the units selected above:

InputValue
Char particle diameter6.0000 mm
Local bed voidage80.000 %
Gas–char slip velocity1.0000 m/s
Gas density0.31000 kg/m³
Gas viscosity0.044000 cP
Oxygen diffusivity in the gas2.0000e-04 m²/s
Oxygen partial pressure in the bulk gas5.0000 kPa
Mean film temperature900.00 °C
Mechanism factor (1 CO₂, 2 CO)1.0000 -

Applying the formula below gives:

ResultValue
Particle Reynolds number42.273
Schmidt number0.70968
Sherwood number6.0739
Mass transfer coefficient, kg C/(m²·s·kPa O₂)2.4910e-04
Diffusion-limited burning rate4.4837 kg/(m²·h)
Carbon burnt per particle0.50710 g/h

Open this example in the calculator and change any input.

Formula

\(Sh = 2\varepsilon + 0.69\left(\frac{Re}{\varepsilon}\right)^{0.5}Sc^{1/3}, \quad h_m = \frac{12\phi\,Sh\,D_g}{d_cRT_m}, \quad q_d = h_mC_g\)

Variables

Symbol Meaning SI unit
\(d_c\) Char particle diameter m
\(\varepsilon\) Local bed voidage -
\(U_g - U_c\) Gas–char slip velocity m/s
\(\rho_g\) Gas density kg/m³
\(\mu\) Gas viscosity Pa·s
\(D_g\) Oxygen diffusivity in the gas m²/s
\(C_g\) Oxygen partial pressure in the bulk gas Pa
\(T_m\) Mean film temperature K
\(\phi\) Mechanism factor (1 CO₂, 2 CO) -
\(Re\) Particle Reynolds number -
\(Sc\) Schmidt number -
\(Sh\) Sherwood number -
\(h_m\) Mass transfer coefficient (shown in kg C per m²·s·kPa O₂) kg/(m²·s·kPa)
\(q_d\) Diffusion-limited burning rate kg/(m²·s)
\(\dot m_p\) Carbon burnt per particle kg/s

Method and standards

Basu's Eqs. (4.7)–(4.10); C_g in kPa, R = 8.314 kPa·m³/(kmol·K).

Where it is used

  • Combustion studies and carbon burnout checks.

Common mistakes

  • Using O₂ mole fraction instead of partial pressure in kPa.
  • Applying outside the fitted size range.

Assumptions and limits

  • Diffusion control; spherical char; correlation fitted for 4–12 mm char (a warning appears outside).
  • Gas density, viscosity and diffusivity are inputs; take them at the mean film temperature \(T_m\) so the set is consistent.
  • The mechanism factor is 1 (CO₂ at the surface) or 2 (CO at the surface); a value between them represents a mixed product.

References

  • Basu
  • Circulating Fluidized Bed Boilers: Design
  • Operation and Maintenance (Springer, 2015)
  • ch. 4
  • Eqs. (4.7)–(4.10) (Halder and Basu 1988)

Questions and answers

When is combustion diffusion-controlled?

For large char particles at high temperature, where chemistry is faster than oxygen can arrive.

What is the mechanism factor?

1 if carbon burns to CO₂ at the surface, 2 if CO forms there and burns away from it.

Why does Sh start at 2ε?

It is the pure-diffusion limit for a sphere in a bed of voidage ε.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.