FireCADCalc

Condenser Vacuum, TTD and Vacuum Efficiency

Absolute pressure and saturation temperature from the condenser vacuum and barometer, with terminal temperature difference, subcooling, vacuum and condenser efficiency.

Thermal power plantSugar mill and cogenerationChemical and fertiliserPulp and paperIAPWS-IF97 (water and steam)Steam turbineCondenser and cooling towerBoiler attendant and boiler operator examinationsBoiler operation engineer (BOE) examinations

Inputs

Examples: 680 mmHg vacuum, 760 mmHg barometer, CW 32 to 41 °C, hotwell 44 °C90 kPa vacuum, 101.3 kPa, CW 30 to 39 °C, hotwell 43 °CHill site: 600 mmHg vacuum, 700 mmHg barometer, CW 28 to 36 °C, hotwell 45 °C

Results

Absolute condenser pressure10.666kPa
Saturation temperature47.074°C
Terminal temperature difference6.0740K
Initial temperature difference15.074K
Cooling water temperature rise9.0000K
Condensate subcooling3.0740K
Vacuum efficiency93.883%
Condenser (cooling water) efficiency59.705%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 680 mmHg vacuum, 760 mmHg barometer, CW 32 to 41 °C, hotwell 44 °C. The inputs, in the units selected above:

InputValue
Vacuum gauge reading (below the barometer)680.00 mmHg
Barometric pressure760.00 mmHg
Cooling water inlet temperature32.000 °C
Cooling water outlet temperature41.000 °C
Condensate (hotwell) temperature44.000 °C

Applying the formula below gives:

ResultValue
Absolute condenser pressure10.666 kPa
Saturation temperature47.074 °C
Terminal temperature difference6.0740 K
Initial temperature difference15.074 K
Cooling water temperature rise9.0000 K
Condensate subcooling3.0740 K
Vacuum efficiency93.883 %
Condenser (cooling water) efficiency59.705 %

Open this example in the calculator and change any input.

Formula

\(p_c = p_{atm} - p_{vac} \qquad T_{sat} = T_{sat}(p_c) \qquad TTD = T_{sat} - T_{cw,2} \qquad ITD = T_{sat} - T_{cw,1}\)

\(\eta_{vac} = \frac{p_{vac}}{p_{atm} - p_{sat}(T_{cw,1})} \qquad \eta_c = \frac{T_{cw,2} - T_{cw,1}}{T_{sat} - T_{cw,1}} \qquad \Delta T_{sub} = T_{sat} - T_{hw}\)

Variables

Symbol Meaning SI unit
\(p_{vac}\) vacuum gauge reading Pa
\(p_{atm}\) barometric pressure Pa
\(T_{cw,1}\) cooling water inlet temperature K
\(T_{cw,2}\) cooling water outlet temperature K
\(T_{hw}\) hotwell (condensate) temperature K
\(p_c\) absolute condenser pressure Pa
\(T_{sat}\) saturation temperature K
\(TTD\) terminal temperature difference K
\(ITD\) initial temperature difference K
\(\Delta T_{cw}\) cooling water rise, \(T_{cw,2} - T_{cw,1}\) K
\(\Delta T_{sub}\) condensate subcooling K
\(\eta_{vac}\) vacuum efficiency –
\(\eta_c\) condenser efficiency –
\(p_{sat}\) saturation pressure of water Pa

Method and standards

Saturation properties by FireCAD's IAPWS-IF97; TTD and ITD as used in the HEI condenser standards; vacuum and condenser efficiencies as defined in steam-plant practice (the usual examination definitions; no single standard governs them). The vacuum is a pressure difference below the barometer, so it is entered in mmHg, kPa or similar, never as a gauge pressure.

Where it is used

  • Daily condenser monitoring in power and cogeneration plants.
  • Troubleshooting poor vacuum: air leaks, fouling, low cooling water flow.
  • Hill and high-altitude sites, where the barometer is well below 760 mmHg.

Common mistakes

  • Taking 760 mmHg as the barometer at every site: at 600 m it is about 710 mmHg.
  • Treating a vacuum reading as absolute pressure.
  • Ignoring subcooling: it wastes heat and lets oxygen dissolve in the condensate.

Assumptions and limits

  • Pure steam saturated at condenser pressure (air partial pressure neglected).
  • The 10 K TTD warning is a FireCAD rule of thumb; a hotwell above saturation is flagged as a reading error.

References

  • IAPWS R7-97(2012) IF97
  • HEI Standards for Steam Surface Condensers (TTD and ITD terms)

Questions and answers

How do I convert condenser vacuum to absolute pressure?

Subtract the vacuum from the barometer. 680 mmHg vacuum with a 760 mmHg barometer leaves 80 mmHg, 10.7 kPa absolute, where steam condenses at 47.0 °C.

What is vacuum efficiency?

Actual vacuum over the best vacuum the cooling water could give, which is the barometer less the saturation pressure at the cooling water inlet temperature. In this example it is 93.9 %; air leaks and fouling lower it.

What TTD is normal?

About 3–6 K for a clean, air-tight condenser. A rising TTD at the same load means fouled tubes, air in the condenser or less cooling water.

Method and article reviewed by FireCAD engineering on 11 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.