FireCADCalc

Grasshopper (Shaker) Sugar Conveyor (Tromp, Hugot)

Throw per stroke, capacity and motor power of a grasshopper sugar conveyor from stroke, speed, strip angle and trough section (Hugot 35.62–35.67, after Tromp).

Sugar mill and cogenerationElectric motor

Inputs

Examples: 40 mm, 300 rpm, 60°Inclined lift 1.5 m

Results

Hugot: stroke about 40 mm at about 300 rpm, strips of ash timber at 60°; incline the conveyor no more than 30° to lift sugar.

Speed of projection cn/200.56000m/s
Throw sin 2(π/2 − α) v²/g27.694mm
Return travel c sin α30.311mm
Capacity11.833t/h
Motor power 2.25 + S_h (kW) plus lift11.299kW

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 40 mm, 300 rpm, 60°. The inputs, in the units selected above:

InputValue
Eccentric stroke40.000 mm
Eccentric speed300.00 rpm
Inclination of the flexible strips60.000 °
Vertical cross-section of sugar in the trough0.030000 m²
Slip coefficient50.000 %
Sugar bulk density850.00 kg/m³
Horizontal surface of the trough12.000 m²
Lift0 m

Applying the formula below gives:

ResultValue
Speed of projection cn/200.60000 m/s
Throw sin 2(π/2 − α) v²/g31.792 mm
Return travel c sin α34.641 mm
Capacity15.246 t/h
Motor power 2.25 + S_h (kW) plus lift14.250 kW

Open this example in the calculator and change any input.

Formula

With \(c\) in m, \(n\) in rpm, \(v\) in m/s, \(S\) in m², \(d\) in kg/m³ and \(Q\) in kg/min, as in Hugot:

\(v = \frac{cn}{20}, \quad r = \sin 2\left(\frac{\pi}{2} - \alpha\right)\frac{v^2}{g}, \quad r' = c\sin\alpha, \quad Q = S(r + r')n k d\)

\(P = 2.25 + S_h\ [\mathrm{kW}] + \frac{QH}{6000}\ [Q\ \mathrm{kg/min}]\)

Variables

Symbol Meaning SI unit
\(c\) Eccentric stroke m
\(n\) Eccentric speed 1/s
\(\alpha\) Inclination of the flexible strips rad
\(S\) Vertical cross-section of sugar in the trough m²
\(k\) Slip coefficient -
\(d\) Sugar bulk density kg/m³
\(S_h\) Horizontal surface of the trough m²
\(H\) Lift m
\(v\) Speed of projection cn/20 m/s
\(r\) Throw sin 2(π/2 − α) v²/g m
\(r'\) Return travel c sin α m
\(Q\) Capacity kg/s
\(P\) Motor power 2.25 + S_h (kW) plus lift W

Method and standards

Tromp's method as given by Hugot.

Where it is used

  • Sugar conveyor design.
  • Checking capacity after a crush increase.

Common mistakes

  • Using the horizontal surface as the section.
  • Ignoring slip.

Assumptions and limits

  • Free-flowing dry sugar.
  • The speed n is in rpm in the formulas (the Variables table gives the SI 1/s); the page converts it.
  • The lift is taken as entered: the conveyor length and slope are not inputs, so Hugot's 30° limit is not checked, and the lift power QH/6000 has no drive efficiency.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 35
  • grasshopper conveyor (after Tromp)
  • eqns 35.62–35.67
  • pp. 814–815

Questions and answers

Why use a grasshopper?

It moves sugar by small throws without crushing crystals.

Where does cn/20 come from?

Hugot takes the grain's projection speed as about 1.5 times the eccentric's mean speed 2cn/60.

Inclined conveyors?

Add the lifting power QH; keep the slope below 30°.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.