Worked example
Example: Delden example, molasses 35. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Massecuite fed | 8.0000 t/h |
| Massecuite brix | 98.000 % |
| Massecuite purity | 56.000 % |
| Sugar purity | 96.000 % |
| Molasses purity | 35.000 % |
| Massecuite density | 1,500.0 kg/m³ |
| Wash water per m³ massecuite | 20.000 - |
| Basket top diameter | 1.0000 m |
| Speed | 1,800.0 rpm |
Applying the formula below gives:
| Result | Value |
|---|---|
| Sucrose in the sugar % massecuite (Delden; crystal plus its molasses film) | 32.388 % |
| Sugar dry solids per massecuite | 33.738 % |
| Sugar (dry solids) | 2.6990 t/h |
| Molasses (dry solids) | 5.1410 t/h |
| Wash water | 106.67 L/h |
| Gravity factor at the rim (top diameter) | 1,811.6 |
| Rim speed | 94.248 m/s |
Open this example in the calculator and change any input.
Formula
\(\frac{S}{Q} = B_m\frac{P_m - P_e}{P_s - P_e}, \quad x = P_s\frac{S}{Q}, \quad \dot m_s = Q\frac{S}{Q}, \quad \dot m_M = Q\left(B_m - \frac{S}{Q}\right)\)
\(\dot V_w = \frac{Q}{\rho_m}\,\frac{w}{1000}, \quad \omega = 2\pi n, \quad G = \frac{\omega^2 D}{2g}, \quad v = \frac{\omega D}{2}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(Q\) | Massecuite fed | kg/s |
| \(B_m\) | Massecuite brix | - |
| \(P_m\) | Massecuite purity | - |
| \(P_s\) | Sugar purity | - |
| \(P_e\) | Molasses purity | - |
| \(\rho_m\) | Massecuite density | kg/m³ |
| \(w\) | Wash water per m³ massecuite (litres per m³) | - |
| \(D\) | Basket top diameter | m |
| \(n\) | Speed | 1/s |
| \(x\) | Sucrose in the sugar % massecuite (Delden; crystal plus its molasses film) | - |
| \(S/Q\) | Sugar dry solids per massecuite | - |
| \(\dot m_s\) | Sugar (dry solids) | kg/s |
| \(\dot m_M\) | Molasses (dry solids) | kg/s |
| \(\dot V_w\) | Wash water | m³/s |
| \(G\) | Gravity factor at the rim (top diameter) | - |
| \(\omega\) | Angular speed | rad/s |
| \(g\) | Standard gravity | m/s² |
| \(v\) | Rim speed | m/s |
Method and standards
Purity balance and centrifugal force.
Where it is used
- Selecting continuous machines.
- Low-grade station balances.
Common mistakes
- Using refractometric brix with gravity purities.
- Ignoring wash dilution of molasses.
Assumptions and limits
- Steady feed; no crystals through the screen.
- Sugar and molasses outputs are dry solids, not product masses; the wash water leaves with the molasses and is not in the dry-solids balance. Crystal dissolved by the wash is accounted for only through the measured molasses purity.
- G and rim speed are at the top (largest) diameter of the conical basket; the mean G over the cone is lower.
References
- Hugot
- Handbook of Cane Sugar Engineering
- 3rd ed. (Elsevier, 1986)
- ch. 35
- continuous centrifugals
- eqns 35.46–35.51 and Delden's crystal content
- pp. 794–806
Questions and answers
Why quote capacity in massecuite?
The machine is limited by the massecuite it can handle; sugar output depends on the crystal content.
Does washing hurt exhaustion?
Yes: continuous machines need some wash on C massecuite, raising molasses purity by up to a point.
Why large casings?
To slow crystals in air before they hit the wall and break.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.