Worked example
Example: 1 065 x 760 at 1 500 rpm. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Basket diameter | 1.0650 m |
| Basket height | 0.76000 m |
| Top speed | 1,500.0 rpm |
| Moment of inertia of basket and charge | 400.00 kg·m² |
| Acceleration time | 60.000 s |
| Speed at which regenerative braking ends (share of top speed) | 60.000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Running friction couple | 100.68 N·m |
| Running power | 15.814 kW |
| Kinetic energy at top speed | 1.3708 kWh |
| Mean power to accelerate | 82.247 kW |
| Energy regenerative braking returns | 0.87730 kWh |
Open this example in the calculator and change any input.
Formula
\(C = D^4 H n_k(1 + 4n_k)\ \mathrm{m\,kgf}\ (n_k = n/1000), \quad P_r = C\omega, \quad E_k = \tfrac12 I\omega^2, \quad P_a = \frac{E_k}{t_a}, \quad E_r = E_k(1 - f^2)\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(D\) | Basket diameter | m |
| \(H\) | Basket height | m |
| \(n\) | Top speed | 1/s |
| \(I\) | Moment of inertia of basket and charge | kg·m² |
| \(t_a\) | Acceleration time | s |
| \(f\) | Speed at which regenerative braking ends (share of top speed) | - |
| \(C\) | Running friction couple | N·m |
| \(P_r\) | Running power | W |
| \(E_k\) | Kinetic energy at top speed | J |
| \(P_a\) | Mean power to accelerate | W |
| \(E_r\) | Energy regenerative braking returns | J |
Method and standards
Hugot's couple with rigid-body energy.
Where it is used
- Sizing centrifugal motors.
- Valuing regenerative drives.
Common mistakes
- Using rpm instead of thousands of rpm in the couple.
- Forgetting the charge in the inertia.
Assumptions and limits
- Rigid basket; constant inertia during acceleration.
- P_a is the kinetic energy over the acceleration time: it excludes the friction power during run-up and the drive efficiency, so a motor sized on it alone is too small. E_r assumes the drive returns all of the braking energy; drive losses reduce it.
- For a 1 065 × 760 mm basket at 1 500 rpm the couple gives about 16 kW, as in Hugot's Table 35.11.
References
- Hugot
- Handbook of Cane Sugar Engineering
- 3rd ed. (Elsevier, 1986)
- ch. 35
- power of centrifugals
- eqns 35.33–35.40 and Table 35.11
- pp. 775–782
- Kinetic energy ½Iω²
Questions and answers
Where does most energy go?
Into accelerating the basket and charge each cycle; running at speed takes much less.
How much does regenerative braking save?
Braking from top speed to 60 % returns 1 − 0.6² = 64 % of the kinetic energy, less drive losses.
Why does the couple rise with speed?
Air drag and bearing friction grow with speed, which Hugot's (1 + 4n) term captures.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.