FireCADCalc

Sugar and Massecuite Screw Conveyor (Hugot)

Capacity, speed and power of a screw conveyor for sugar or massecuite from diameter, pitch, speed and fill (Hugot eqns 35.57–35.61).

Sugar mill and cogenerationElectric motor

Inputs

Examples: Sugar screw 0.5 mMassecuite screw

Hugot: about 0.7 D.
Hugot: sugar 15–25 rpm or 10/D; massecuite 15/D (Tromp 7–8).
Hugot: sugar 0.10–0.12 ribbon, 0.15–0.20 full; massecuite 0.15–0.20 ribbon, 0.25–0.30 full.
About 850 kg/m³ for sugar; massecuite is much denser (about 1 450–1 500 kg/m³). Change it when you choose massecuite.

Results

The power is Hugot's rule in D²L only: it does not change with speed or throughput.

Hugot: leave 6 mm between screw and trough so as not to crush crystals; support the shaft every 3 m. Add the drive efficiency to the power.

Volume conveyed12.370m³/h
Mass conveyed10.515t/h
Hugot's speed (10/D sugar, 15/D massecuite)20.000rpm
Power (0.8 D²L sugar, 1.15 D²L massecuite)4.0000kW

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Sugar screw 0.5 m. The inputs, in the units selected above:

InputValue
MaterialSugar
Screw diameter0.50000 m
Pitch0.35000 m
Speed20.000 rpm
Fill and slip coefficient15.000 %
Bulk density850.00 kg/m³
Screw length20.000 m

Applying the formula below gives:

ResultValue
Volume conveyed12.370 m³/h
Mass conveyed10.515 t/h
Hugot's speed (10/D sugar, 15/D massecuite)20.000 rpm
Power (0.8 D²L sugar, 1.15 D²L massecuite)4.0000 kW

Open this example in the calculator and change any input.

Formula

\(\dot V = \frac{\pi D^2}{4}p\,n\,k, \quad \dot m = d\dot V, \quad P = 0.8D^2L\ (\text{sugar}),\ 1.15D^2L\ (\text{massecuite})\ [\mathrm{kW}]\)

Variables

Symbol Meaning SI unit
\(\text{material}\) Material -
\(D\) Screw diameter m
\(p\) Pitch m
\(n\) Speed 1/s
\(k\) Fill and slip coefficient -
\(d\) Bulk density kg/m³
\(L\) Screw length m
\(\dot V\) Volume conveyed m³/s
\(\dot m\) Mass conveyed kg/s
\(n_H\) Hugot's speed (10/D sugar, 15/D massecuite) 1/s
\(P\) Power (0.8 D²L sugar, 1.15 D²L massecuite) W

Method and standards

Hugot's screw conveyor rules.

Where it is used

  • Sizing sugar and massecuite screws.
  • Checking conveyor power.

Common mistakes

  • Using k = 1.
  • Forgetting drive losses.

Assumptions and limits

  • Horizontal screws.
  • Hugot's power rule depends on size only, not on speed or throughput; a speed well above his n_H is flagged.
  • The bulk density is not changed with the material: enter about 1 450–1 500 kg/m³ for massecuite.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 35
  • screw conveyors for massecuite and sugar
  • eqns 35.57–35.61
  • pp. 812–814

Questions and answers

What is k?

The share of the swept volume actually moved: the trough is never full and material slips back.

Why do screws crush sugar?

Crystals caught between flight and trough break; Hugot prefers grasshopper conveyors for sugar.

Massecuite speed?

Slow: Tromp recommends 7–8 rpm to avoid back-flow.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.