Worked example
Example: 40 mm, 300 rpm, 60°. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Eccentric stroke | 40.000 mm |
| Eccentric speed | 300.00 rpm |
| Inclination of the flexible strips | 60.000 ° |
| Vertical cross-section of sugar in the trough | 0.030000 m² |
| Slip coefficient | 50.000 % |
| Sugar bulk density | 850.00 kg/m³ |
| Horizontal surface of the trough | 12.000 m² |
| Lift | 0 m |
Applying the formula below gives:
| Result | Value |
|---|---|
| Speed of projection cn/20 | 0.60000 m/s |
| Throw sin 2(π/2 − α) v²/g | 31.792 mm |
| Return travel c sin α | 34.641 mm |
| Capacity | 15.246 t/h |
| Motor power 2.25 + S_h (kW) plus lift | 14.250 kW |
Open this example in the calculator and change any input.
Formula
With \(c\) in m, \(n\) in rpm, \(v\) in m/s, \(S\) in m², \(d\) in kg/m³ and \(Q\) in kg/min, as in Hugot:
\(v = \frac{cn}{20}, \quad r = \sin 2\left(\frac{\pi}{2} - \alpha\right)\frac{v^2}{g}, \quad r' = c\sin\alpha, \quad Q = S(r + r')n k d\)
\(P = 2.25 + S_h\ [\mathrm{kW}] + \frac{QH}{6000}\ [Q\ \mathrm{kg/min}]\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(c\) | Eccentric stroke | m |
| \(n\) | Eccentric speed | 1/s |
| \(\alpha\) | Inclination of the flexible strips | rad |
| \(S\) | Vertical cross-section of sugar in the trough | m² |
| \(k\) | Slip coefficient | - |
| \(d\) | Sugar bulk density | kg/m³ |
| \(S_h\) | Horizontal surface of the trough | m² |
| \(H\) | Lift | m |
| \(v\) | Speed of projection cn/20 | m/s |
| \(r\) | Throw sin 2(π/2 − α) v²/g | m |
| \(r'\) | Return travel c sin α | m |
| \(Q\) | Capacity | kg/s |
| \(P\) | Motor power 2.25 + S_h (kW) plus lift | W |
Method and standards
Tromp's method as given by Hugot.
Where it is used
- Sugar conveyor design.
- Checking capacity after a crush increase.
Common mistakes
- Using the horizontal surface as the section.
- Ignoring slip.
Assumptions and limits
- Free-flowing dry sugar.
- The speed n is in rpm in the formulas (the Variables table gives the SI 1/s); the page converts it.
- The lift is taken as entered: the conveyor length and slope are not inputs, so Hugot's 30° limit is not checked, and the lift power QH/6000 has no drive efficiency.
References
- Hugot
- Handbook of Cane Sugar Engineering
- 3rd ed. (Elsevier, 1986)
- ch. 35
- grasshopper conveyor (after Tromp)
- eqns 35.62–35.67
- pp. 814–815
Questions and answers
Why use a grasshopper?
It moves sugar by small throws without crushing crystals.
Where does cn/20 come from?
Hugot takes the grain's projection speed as about 1.5 times the eccentric's mean speed 2cn/60.
Inclined conveyors?
Add the lifting power QH; keep the slope below 30°.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.