FireCADCalc

Centrifugal Gravity Factor and Mean Radius (Hugot)

Gravity factor of a centrifugal at the basket wall and at Hugot's mean equivalent radius of the sugar layer (eqns 35.16–35.17), with the peripheral speed.

Sugar mill and cogeneration

Inputs

Examples: Hugot example 1 220 mmHigh-speed C machine

Results

Hugot's example: 1 220 mm basket, 203 mm layer, 1 500 rpm: mean radius 0.515 m and G about 1 297.

Mean equivalent radius442.73mm
Gravity factor at the basket wall2,236.5
Gravity factor at the mean radius1,980.3
Peripheral speed104.72m/s

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Hugot example 1 220 mm. The inputs, in the units selected above:

InputValue
Basket diameter1.2200 m
Thickness of the massecuite layer203.00 mm
Speed1,500.0 rpm

Applying the formula below gives:

ResultValue
Mean equivalent radius515.25 mm
Gravity factor at the basket wall1,534.8
Gravity factor at the mean radius1,296.4
Peripheral speed95.819 m/s

Open this example in the calculator and change any input.

Formula

\(R = \frac{D}{2}, \quad r = R - e, \quad R_m = \frac23\frac{R^3 - r^3}{R^2 - r^2}, \quad G_R = \frac{\omega^2 R}{g}, \quad G_m = \frac{\omega^2 R_m}{g}, \quad v = \omega R, \quad \omega = 2\pi n\)

Variables

Symbol Meaning SI unit
\(D\) Basket diameter m
\(e\) Thickness of the massecuite layer m
\(n\) Speed 1/s
\(R_m\) Mean equivalent radius m
\(G_R\) Gravity factor at the basket wall -
\(G_m\) Gravity factor at the mean radius -
\(v\) Peripheral speed m/s
\(R\), \(r\) basket radius and inner radius of the layer m
\(\omega\) angular speed rad/s
\(g\) standard gravity m/s²

Method and standards

Centrifugal force on the layer.

Where it is used

  • Comparing centrifugals.
  • Choosing machines for low grades.

Common mistakes

  • Using diameter as radius.
  • Quoting G at the wall for a thick layer.

Assumptions and limits

  • Uniform layer. A layer up to the radius is accepted; a note appears above Hugot's working limit of about 0.14 D.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 35
  • eqns 35.4 and 35.16–35.17
  • pp. 760–766

Questions and answers

Why a mean radius?

The layer is thick: the inner sugar feels less force than that against the screen; Hugot's mean radius weights the whole layer.

What G for low grades?

High-speed machines for C massecuite run at 1 800–2 000 G or more.

Does purging time depend on G?

Hugot: the drying time varies inversely with n², and with D n² for different diameters.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.