FireCADCalc

Torsion of Thin-Walled Closed Tubes (Bredt)

Shear stress and angle of twist of a thin-walled closed rectangular tube under torque by Bredt's formulas, from the mean dimensions and wall thickness.

Inputs

Examples: 2 kN·m, 100 × 60 mm box, 4 mm, 2 mSquare 200 mm, 6 mm, 15 kN·m, 3 mAluminium 80 × 40, 3 mm, 500 N·m, 1 m, 26 GPa

Results

Thin uniform wall (t much less than b and h); corners raise the stress locally.

Area enclosed by the wall centre line3,200.0mm²
Shear stress T/(2 A_m t)26.042MPa
Torsion constant 4A_m² t/s51.200cm⁴
Angle of twist2.1520°

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 2 kN·m, 100 × 60 mm box, 4 mm, 2 m. The inputs, in the units selected above:

InputValue
Torque2,000.0 N·m
Mean width (centre line of the wall)100.00 mm
Mean height60.000 mm
Wall thickness4.0000 mm
Length2.0000 m
Shear modulus79.000 GPa

Applying the formula below gives:

ResultValue
Area enclosed by the wall centre line6,000.0 mm²
Shear stress T/(2 A_m t)41.667 MPa
Torsion constant 4A_m² t/s180.00 cm⁴
Angle of twist1.6117 °

Open this example in the calculator and change any input.

Formula

\(\tau = \frac{T}{2 A_m t}, \quad J = \frac{4 A_m^2 t}{s}, \quad \theta = \frac{T L}{G J}\)

Variables

Symbol Meaning SI unit
\(T\) Torque N·m
\(b\) Mean width (centre line of the wall) m
\(h\) Mean height m
\(t_w\) Wall thickness m
\(L\) Length m
\(G\) Shear modulus Pa
\(A_m\) Area enclosed by the wall centre line m²
\(\tau\) Shear stress T/(2 A_m t) Pa
\(J\) Torsion constant 4A_m² t/s m⁴
\(\theta\) Angle of twist rad

Method and standards

Constant shear flow around a thin closed section.

Where it is used

  • Frames, booms and chassis members.
  • Strength of materials examinations.

Common mistakes

  • Outside dimensions instead of mean.
  • Using it for open sections.

Assumptions and limits

  • The page warns when the wall exceeds a tenth of the smaller mean dimension (approximate) and when it reaches half of it (thin-wall theory invalid).

  • Thin, uniform wall.

References

  • Bredt–Batho thin-walled tube theory (Timoshenko, Strength of Materials)

Questions and answers

2 kN·m on a 100 × 60 mm box, 4 mm wall?

41.7 MPa shear.

Why are closed sections so stiff in torsion?

The torsion constant grows with the enclosed area squared; an open section of the same metal twists hundreds of times more.

Which dimensions?

To the centre line of the wall.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.