FireCADCalc

Thick-Walled Sphere under Internal Pressure (Lamé)

Radial and hoop stresses in a thick-walled sphere under internal pressure by the Lamé solution, at the inner and outer surfaces, compared with the thin-wall result.

Inputs

Examples: 50 MPa, 100 / 150 mm200 MPa, 50 / 100 mmThin-ish: 2 MPa, 1 000 / 1 010 mm

Results

Elastic Lamé solution; compare the stress intensity with the material's yield or the code's allowable. Design of pressure vessels follows the applicable code.

Hoop stress at the inner surface142.86MPa
Hoop stress at the outer surface42.857MPa
Radial stress at the inner surface (−p)-200.00MPa
Thin-wall hoop stress p r_i/(2t)100.00MPa
Stress intensity at the inner surface (Tresca)342.86MPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 50 MPa, 100 / 150 mm. The inputs, in the units selected above:

InputValue
Internal pressure50.000 MPa
Inner radius100.00 mm
Outer radius150.00 mm

Applying the formula below gives:

ResultValue
Hoop stress at the inner surface56.579 MPa
Hoop stress at the outer surface31.579 MPa
Radial stress at the inner surface (−p)-50.000 MPa
Thin-wall hoop stress p r_i/(2t)50.000 MPa
Stress intensity at the inner surface (Tresca)106.58 MPa

Open this example in the calculator and change any input.

Formula

\(\sigma_t(r) = \frac{p\, r_i^3 (r_o^3 + 2r^3)}{2 r^3 (r_o^3 - r_i^3)}, \quad \sigma_r(r) = -\frac{p\, r_i^3 (r_o^3 - r^3)}{r^3 (r_o^3 - r_i^3)}\)

Variables

Symbol Meaning SI unit
\(p\) Internal pressure Pa
\(r_i\) Inner radius m
\(r_o\) Outer radius m
\(\sigma_{t,i}\) Hoop stress at the inner surface Pa
\(\sigma_{t,o}\) Hoop stress at the outer surface Pa
\(\sigma_{r,i}\) Radial stress at the inner surface (−p) Pa
\(\sigma_{thin}\) Thin-wall hoop stress p r_i/(2t) Pa
\(\sigma_{t,i} - \sigma_{r,i}\) Stress intensity at the inner surface (Tresca) Pa

Method and standards

Lamé solution for spherical symmetry.

Where it is used

  • High-pressure spheres and heads.
  • Strength of materials examinations.

Common mistakes

  • Using cylinder formulas.
  • Diameter for radius.

Assumptions and limits

  • The stress intensity σ_t − σ_r at the inner surface is the Tresca equivalent stress; no yield or code check is made.

  • Elastic, internal pressure only.

References

  • Lamé solution for a thick sphere (Timoshenko and Goodier, Theory of Elasticity)

Questions and answers

50 MPa in a sphere of 100 and 150 mm radii?

Inner hoop stress 56.6 MPa; thin-wall theory gives 50 MPa.

Why does a sphere need half the thickness of a cylinder?

Its hoop stress is half the cylinder's for the same pressure and radius.

When is thin-wall theory fine?

Wall thickness under about a tenth of the radius.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.