Worked example
Example: Rectangle 200 x 400 mm. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Section | Solid rectangle (b × h) |
| Width, flange width or outside diameter | 200.00 mm |
| Depth (rectangles and I-section) | 400.00 mm |
| Wall thickness, or flange thickness of the I-section | 12.000 mm |
| Web thickness (I-section) | 8.0000 mm |
Applying the formula below gives:
| Result | Value |
|---|---|
| Area | 800.00 cm² |
| Second moment of area about the x axis (strong, horizontal) | 106,667 cm⁴ |
| Elastic section modulus about x | 5,333.3 cm³ |
| Radius of gyration about x | 115.47 mm |
| Second moment of area about the y axis | 26,667 cm⁴ |
| Elastic section modulus about y | 2,666.7 cm³ |
| Radius of gyration about y | 57.735 mm |
Open this example in the calculator and change any input.
Formula
\(I_x = \frac{b h^3}{12}, \quad I_x = \frac{b h^3 - (b - t_w)(h - 2t)^3}{12}\ (\text{I}), \quad I = \frac{\pi D^4}{64}\ (\text{round})\)
\(Z = \frac{I}{c}, \quad r = \sqrt{I / A}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\text{shape}\) | Section | - |
| \(b\) | Width, flange width or outside diameter | m |
| \(h\) | Depth (rectangles and I-section) | m |
| \(t\) | Wall thickness, or flange thickness of the I-section | m |
| \(t_w\) | Web thickness (I-section) | m |
| \(A\) | Area | m² |
| \(I_x\) | Second moment of area about the x axis (strong, horizontal) | m⁴ |
| \(Z_x\) | Elastic section modulus about x | m³ |
| \(r_x\) | Radius of gyration about x | m |
| \(I_y\) | Second moment of area about the y axis | m⁴ |
| \(Z_y\) | Elastic section modulus about y | m³ |
| \(r_y\) | Radius of gyration about y | m |
| \(c\) | Distance from the axis to the extreme fibre | m |
Method and standards
Second moments of area of standard shapes about their centroidal axes; the elastic section modulus divides by the distance to the extreme fibre.
Where it is used
- Beam and column checks.
- Comparing fabricated sections.
- Pipe and tube stiffness.
Common mistakes
- Mixing strong and weak axes.
- Using plastic modulus where elastic is meant.
- Ignoring root radii of rolled sections.
Assumptions and limits
- Sharp-cornered, doubly symmetric shapes.
References
- Second moments of area of standard shapes (Roark's Formulas for Stress and Strain, Table A.1)
Questions and answers
What are the properties of a 200 × 400 mm rectangle?
A = 800 cm², I_x = 106 700 cm⁴ and Z_x = 5 333 cm³ about the strong axis.
How is an I-section found?
As the outer rectangle less the two side voids: I_x = [b h³ − (b − t_w)(h − 2t)³]/12.
What is the radius of gyration for?
√(I/A) sets the slenderness of a column; it feeds the buckling check.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.