FireCADCalc

Section Properties: Area, Moment of Inertia, Section Modulus

Area, second moment of area, section modulus and radius of gyration of rectangular, hollow rectangular, round, tube and I-sections about both axes.

Inputs

Examples: Rectangle 200 x 400 mmHollow 150 x 250 x 8 mmPipe 168.3 x 7.11 mmRound bar 50 mmI-section 150 x 300 mm, flanges 12 mm, web 8 mm

Results

Sharp corners: root radii of rolled sections add a little area and stiffness; use the maker's tables for rolled sections.

Area61.440cm²
Second moment of area about the x axis (strong, horizontal)5,223.5cm⁴
Elastic section modulus about x417.88cm³
Radius of gyration about x92.205mm
Second moment of area about the y axis2,339.3cm⁴
Elastic section modulus about y311.91cm³
Radius of gyration about y61.705mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Rectangle 200 x 400 mm. The inputs, in the units selected above:

InputValue
SectionSolid rectangle (b × h)
Width, flange width or outside diameter200.00 mm
Depth (rectangles and I-section)400.00 mm
Wall thickness, or flange thickness of the I-section12.000 mm
Web thickness (I-section)8.0000 mm

Applying the formula below gives:

ResultValue
Area800.00 cm²
Second moment of area about the x axis (strong, horizontal)106,667 cm⁴
Elastic section modulus about x5,333.3 cm³
Radius of gyration about x115.47 mm
Second moment of area about the y axis26,667 cm⁴
Elastic section modulus about y2,666.7 cm³
Radius of gyration about y57.735 mm

Open this example in the calculator and change any input.

Formula

\(I_x = \frac{b h^3}{12}, \quad I_x = \frac{b h^3 - (b - t_w)(h - 2t)^3}{12}\ (\text{I}), \quad I = \frac{\pi D^4}{64}\ (\text{round})\)

\(Z = \frac{I}{c}, \quad r = \sqrt{I / A}\)

Variables

Symbol Meaning SI unit
\(\text{shape}\) Section -
\(b\) Width, flange width or outside diameter m
\(h\) Depth (rectangles and I-section) m
\(t\) Wall thickness, or flange thickness of the I-section m
\(t_w\) Web thickness (I-section) m
\(A\) Area m²
\(I_x\) Second moment of area about the x axis (strong, horizontal) m⁴
\(Z_x\) Elastic section modulus about x m³
\(r_x\) Radius of gyration about x m
\(I_y\) Second moment of area about the y axis m⁴
\(Z_y\) Elastic section modulus about y m³
\(r_y\) Radius of gyration about y m
\(c\) Distance from the axis to the extreme fibre m

Method and standards

Second moments of area of standard shapes about their centroidal axes; the elastic section modulus divides by the distance to the extreme fibre.

Where it is used

  • Beam and column checks.
  • Comparing fabricated sections.
  • Pipe and tube stiffness.

Common mistakes

  • Mixing strong and weak axes.
  • Using plastic modulus where elastic is meant.
  • Ignoring root radii of rolled sections.

Assumptions and limits

  • Sharp-cornered, doubly symmetric shapes.

References

  • Second moments of area of standard shapes (Roark's Formulas for Stress and Strain, Table A.1)

Questions and answers

What are the properties of a 200 × 400 mm rectangle?

A = 800 cm², I_x = 106 700 cm⁴ and Z_x = 5 333 cm³ about the strong axis.

How is an I-section found?

As the outer rectangle less the two side voids: I_x = [b h³ − (b − t_w)(h − 2t)³]/12.

What is the radius of gyration for?

√(I/A) sets the slenderness of a column; it feeds the buckling check.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.