FireCADCalc

Stress in a Rotating Ring and Solid Disc

Hoop stress in a thin rotating ring and the maximum stresses in a solid rotating disc of uniform thickness from speed, radius, density and Poisson's ratio.

Inputs

Examples: 400 mm radius steel disc, 3 000 rpmAluminium fan 250 mm, 6 000 rpmGrinding wheel 150 mm, 3 600 rpm, 2 500 kg/m³, 0.2

Results

Uniform thickness, elastic, plane stress. A central hole doubles the hoop stress at the bore.

Rim speed56.549m/s
Hoop stress in a thin ring ρ v²7.9944MPa
Maximum stress in a solid disc (centre)3.1978MPa
Hoop stress at the rim of the solid disc1.5989MPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 400 mm radius steel disc, 3 000 rpm. The inputs, in the units selected above:

InputValue
Outer radius400.00 mm
Speed3,000.0 rpm
Density7,850.0 kg/m³
Poisson's ratio0.30000 -

Applying the formula below gives:

ResultValue
Rim speed125.66 m/s
Hoop stress in a thin ring ρ v²123.96 MPa
Maximum stress in a solid disc (centre)51.134 MPa
Hoop stress at the rim of the solid disc21.693 MPa

Open this example in the calculator and change any input.

Formula

\(\sigma_{ring} = \rho v^2, \quad \sigma_{max} = \frac{3 + \nu}{8}\rho\omega^2 r_o^2, \quad \sigma_{t,rim} = \frac{1 - \nu}{4}\rho\omega^2 r_o^2\)

Variables

Symbol Meaning SI unit
\(r_o\) Outer radius m
\(N\) Speed 1/s
\(\rho\) Density kg/m³
\(\nu\) Poisson's ratio -
\(v\) Rim speed m/s
\(\sigma_{ring}\) Hoop stress in a thin ring ρ v² Pa
\(\sigma_{max}\) Maximum stress in a solid disc (centre) Pa
\(\sigma_{t,rim}\) Hoop stress at the rim of the solid disc Pa

Method and standards

Elastic solution for a rotating disc.

Where it is used

  • Flywheels, fans and grinding wheels.
  • Strength of materials examinations.

Common mistakes

  • Diameter for radius.
  • Ignoring a bore.

Assumptions and limits

  • Solid disc, uniform thickness. A disc with a central bore is not covered: even a small hole about doubles the hoop stress at the bore compared with the solid-disc centre value.
  • Stresses are not compared with an allowable stress or a burst speed; check them against the material's strength with your design margin.

References

  • Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 3 (rotating rings and discs, (3 + ν)/8 ρ ω² r²)

Questions and answers

A 400 mm radius steel disc at 3000 rpm?

Rim speed 126 m/s; centre stress 51.1 MPa.

Why does a thin ring see more?

It has no inner material to share the load: σ = ρ v².

What limits flywheels?

Rim speed, since stress depends only on ρ v².

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.